Search results

I had a TX1500 for about 20 years. It would not start in cold weather even with glow plugs. A battery out of an 86 V-8 Mustang will just fit with a little help and covering the battery terminals when installed. Be sure to replace battery cables with larger ones. Even with a bigger battery it...

I just had a pipe threading project. I went to a used tool store. I found a nice quality hardly used Rigid thread die and ratcheting handle for $50. The tool store owner said he would buy it back for $25 when I am done. I felt like this was a good deal for both of us.

My B7800 does not have clearance for tire chains. Does anyone know of 1 inch spacers that I could install between hub and wheel for chain clearance?

I have an older B7800 with a LA-402 loader. The Kabota salesman told me that there were no conversion kits made to convert my loader to a quick disconnect modern style. He indicates I need to buy a new loader. Is that correct?

I have a B7800 tractor. My wife would like to spot spray for weeds and non native grass. A 3 point tank and a PTO driven pump with a hand held spray nozzle. Any body have a recommendation?

Great Idea---why didn't I think of that!

I have a B7800 Kabota that I bought 6 mos. ago. I told my wife about the idea she could use it for spaying weeds from the operators seat with a hose and a trigger operated valve. She likes the idea. I showed her the controls and she took it out for a spin (tractor style.). I can see my wife...

I just bought a B7800 HSD. I ordered an operators manual, parts manual and work shop manual. I just received my manuals and I could wait till Monday and ask the Kabota dealer where I bought the manuals but I would like to open them if they are correct. My work shop manual front cover has...

Replaced the eight year old battery in my B7800. Before I removed my old battery I checked charging voltage and it was 12.4 volts. I installed my new NAPA Legend battery and it was still charged at 12.4 volts. I am waiting for my manual so I have to rely on you guys. My experience tells me...

New to me B7800 Kabota. I will be leaving my tractor in a shed but open to the weather. We have -10 degrees in the winter, are the glow plugs adequate to start it or do I need a block heater?

My B7800 new to me. When on gravel or dirt and turning sharp the inside rear tire jumps and spins a little. The differential lock is not engaged. Is this normal?

I have a new to me B7800 HSD Kabota tractor. I use my right foot to activate the hydrostatic drive. When I remove my right foot the tractor stops immediately. How do you use the foot brakes for steering assist when you are pulling hard? Or when you are pushing a lot of snow and you need...

I am in the market to buy a snow bade for my B7800. The local Kubota dealer recommends Land Pride from Kansas City. Are these any good? What are you using?

Sold my Iseki TX 1500F today. Picking it up tomorrow. Posted it on Craigs list at 9 PM by 7AM I had three people that wanted to see it. By noon 12 inquiries. The second person who looked at it bought it. My father-in-law bought it new, always parked inside. It had original paint, I think...

B7800 tractor and loader I just moved up from my 17HP Iseki to a 29 HP B7800 Kabota. It has a loader model LA402-1. This tractor was used for cleaning up horse manure so they bought the cheap loader. The bucket does not detach from the loader frame. I bought the tractor for snow...

I have a TX1500F Iseki tractor. For those of you not recognizing the model it is a two cylinder diesel, 4 wheel drive, of about 1978 vintage. The fuel filter started leaking, it is original style to the tractor. It has vents that can be opened for bleeding the system. Does anyone know of a...

I hope I am in the right forum. Does anyone know where there is information about pricing a Land Trac 360 to sell. Automobiles have Kelly Blue Book, do tractors have something similar? My neighbor asked me to help her sell her tractor and implements (husband died).

Hope this works. The gage is mounted by the air cleaner and the temp sender mounted to the thermostat housing

I maintain a Landtrac 360 DTC 4X4, it is only used for plowing snow. It is used very little and only has a couple hundred hours on it. I do not know the year but from other threads on here about adding hydraulic oil it is of the early model with the sight plug. I replaced the front ring and...

I had to retire my my 25 year old Honda lawn mower. I bought a new Toro lawn mower. My wife mows the lawn and right away she points out the new Toro does not have a blade brake so you have to restart the engine every time you change bags, it is front wheel drive and when the bag gets full the...

I am tired of paying annual rent and being tied to one supplier for propane so I purchased an older 500 gal. propane tank. I want to update the valves on the tank. Being a do it yourself type of guy I discovered all the local propane suppliers do not want to sell propane tank parts to a...

I have a TX 1500 F Iseki with the KE 75 2 cylinder engine. I have noticed several threads mentioning about hard starting. I have also noted on here about mine hard starting in cold weather until I installed a block heater. But what do you do if you can not plug it in. When I am working out...

I have a TU 1500F Iseki, great little tractor(old). Is Iseki still in business and if yes where in the world are they marketed. My tractor was sold new to my father-in-law in the late 70's. The Bolens dealer went out of business. As far as I can tell there has not been any more Isekis sold...

I grew up around John Deere tractors A's B's and then newer 4 cylinders and then a big 4020. My wife saw this Model 50 the other day with a FEL. I do not remember ever seeing a 50 series tractor. Were they as dependable as the old A and B models? It is a 1952 model with a single tire front...

I hope I am in the right forum. I take care of a Landtrac Model 360DTC tractor for a man who removes snow from driveways during the winter. He mounts a front end loader on it during the summer and moves around gravel with it. He said I could use it to move some logs. He does not have any...

I have an old Iseki Model TX1500F (Bolens 174). The operator manual indicates "Bolens offer an engine block heater that can be installed by dealer." Is any one familiar with this item. I am wondering how it was plumbed into the cooling system.

I have a Iseki TX1500F (Bolens G-174). It is a two cylinder diesel model and I was quoted $700 plus for a muffler. All I had left of my muffler was the pipes coming from the exhaust ports. I fabricated new exhaust flanges, welded ports on, then welded a manifold on and attached a vertical...

I inherited an Iseki TX 1500F from my father-in-law. Everything works fine, but it needs a muffler. A snow plow and a snow blower are in my dreams.