Search results

I have a howse 5' brush hog. The U joint broke off. Are these special u-joints or can I get them at any autoparts store? I went to one and got an automotive one and it was 1/16th" to long (couldnt get the clip to set in) and TSC didnt have one either it was way to long or too short. Thanks

I have an Agco Challenger MT275 40.1hp Diesel tractor with sync shuttle shift. The way mine engages is there is a lever on the left side floorboard that you press down to engage 4wd. I was using it today using the FEL and had no issues. I went in to go rest and eat a few bites and now it...

Has anyone made skid plates for your hydraulic hoses. Im wanting to make 2 one that goes on top of my loader arms. So when Im pushing up a brush pile and a log slips it wont take out my hoses and the other that goes under the tractor right off my control valve and to the transmission. I was...

I like the installing the gauge. How and where do you install it? Does any one have any pics of theirs installed? How do I increase it once I get the gauge installed?

How do I or can I increase the power in my hydraulics. I understand (and I know its not on all tractors and I'm not sure if mine is one of them) but I hear there is an adjuster screw to in crease hydraulic pressure. Which I know I'll get a pressure gauge and find out what the max pressure is...

I have a Challenger MT275 with a Nimco control valve type 25-40394 date 03-30 serial# 225148 It was leaking where the cable from your joystick goes to the hydraulic valve block. I took out the cable and there was a white nylon washer that looked like it was crushed and a loose fitting oring...

Here is a vid I did on installing the tooth bar in case anyone was interested How to install a tooth bar (toothbar) and Review Harbor Freight drill bit set #00527 - YouTube Tooth Bar installed and Turn an Ammo can into a tool box - YouTube

Here's the Quick hitch from Harbor Freight. Harbor Freight Quick Hitch Item# 97214 (part I unboxing) - YouTube Installation of quick hitch Harbor Freight Quick Hitch Item# 97214 (part II attaching to 3 point on tractor) - YouTube Using the quick hitch and attaching the quick hitch to brush...

I turned an old ammo can into a tool box for the tractor. Works great and water tight. Tooth Bar installed and Turn an Ammo can into a tool box - YouTube

I have a MT275 Challenger with a ML30 FEL. I carb cleaned it off the day before. So where you see it's wet is the leak. I don't know if it's the top flang thing or the bottom one But the silver part is where it's leaking.

I need to change out the fluid in my gear box it looks milky. 1) how do you do it? I didn't see a drain plug any where 2) what gear oil should I use 3) should I use the Lucas gear oil in there? Thanks in advance (I've only put 7 hrs on this used unit)

I need a starter for my 1950 8N. Mine just crapped out on me. It spins freely but 12V @ 2amps wont spin it 12V @ 40amps barely spins it and 12v @ 200amps spins but gets really hot.

So I've had this tractor for a over a year now and have never had this much problems with it. So I've replaced points and condenser. No spark changed coil. (it was getting really hot and leaking oil out of the top and it was pretty old so I replaced it anyways) still no spark, Replaced resistor...

Yeah it was pretty bad. I pulled the 2 drain holes and milky oil came out. I did check to see if the gaskets around the fill plug were bad but they seem pretty good. So I wonder where the water came from. The axle is dry as a bone on the out side. Oh well I drained it all out and flushed it...

So I changed the tranny/hydraulic fluid last night. The manual calls for like 8.7gal of fluid I put in almost 12 gal and it is still not showing up on the sight glass. First I made sure no leaks (:thumbsup:) then I started it up and ran it around the yard a bit eveything works fine no wierd...

I have a leak on some kind of valve block thing (see vid) It's on a Challenger MT275 tractor with a ML30 Front End Loader. p.s. Save your self some time and Fast Forward to 8:26 YouTube - ‪MT275 updates‬‏

Just an FYI oil filter 3757038M2 is a NAPA 1348. It was crossed with another oil filter (NAPA 1335) but it didn't work :mad: ARGHH but I went down there and a 1348 works perfect!!! No for the Hydraulic filter (theirs didn't match up ARGHHH)

I have a AGCO/CAT Challenger MT275 it calls for a 3607790M1 spin on hydralic filter. The dealer want almost $60.00 is there a way to get an aftermarket one?:confused: Thanks in advance

I have a AGCO/CAT Challenger MT275 it calls for a 3607790M1 spin on hydralic filter. The dealer want almost $60.00 is there a way to get an aftermarket one? Thanks in advance

Just wanted to stop in and say hello. I had an 1950 8N and it crapped out on me so I bought an AGCO/CAT Challenger MT275 40hp 4x4 front end loader turbo diesel. I haven't even got to use it yet :( First time will be tomorrow (can't wait) Here's a vid on the first day I bought it...