Search results

I have pretty much the same trailer your buying used if your interested. It’s rated 15k Report

I have pretty much the same trailer your buying used if your interested. It’s rated 15k

I picked up a Massey Ferguson 1260 which is an Iseki Tk538, where can I get parts, new or used ?!

No one ?

My power steering leaks on the 2 steering arms shafts on both sides. Is it difficult to replace these seals ? Would the power steering work even though they leak ?

It needs to have a slip joint,correct. how do I measure where the slip should be and with mower up, down, should I run an override coupler ?

Darn, no one has this mower ?

So you used the same paint and it held up good on the motor ?

Does anyone have the specs for the driveshaft for a 5 foot Ford Flail 907, as far as length etc. I'm thinking 1-3/8" spline both ends, but no idea on length. Of course I bought this mower, and it had no driveshaft !

I always painted motors with heat paint, but never a tractor, figured it might be different because it's out in the open. I'm gonna pull all the tin, have it media blasted and shoot them separate.

I can paint, I've got a cheap Devilibiss primer gun, and a $400 Sata I use for finish on cars, just wasn't sure if any of these paints were designed to be used with high temps also ?

So with the Sherwin Williams or OEM paint we can paint the motor too ? We’re gonna mask everything off

I see a lot of guys here with freshly painted tractors, do you just spray everything even the motor with the same paint ?

I’m gonna repaint my Ford 2000 with Majic paint, I’ve had good luck with this paint, but wondering has anyone used it in the motor, can it withstand high temps, or do you have to use motor specific paint ?

When I raise the bed on my 2012 5600 Toolcat there is a buzzing sound coming from the bed. Anyone have any ideas. Only when raising the bed. All other hydraulics work quiet.

Has anyone ever used an attachment like this Case D125 skid steer backhoe, I'm thinking a quick tach plate can be welded on ? Would it be too much for a Toolcat ? Here's a video of one IMG 2124 - YouTube

Hey has anyone found an aftermarket seat to replace the drivers side typical ripped seat ?? Do not wanna buy an overpriced Bobcat seat !

Can someone confirm the size of the turf tire wheel ? The turfs use a 15x10 wheel (pn 6688857), if you look up the part number it states it has 6 x 5.5 (139.7mm) 6 lug BC with a 5" pilot hole, but nowhere can I verify the backset, which in one thread I found was 4 inches, but would love to...

So Id like to put something like the Carlisle Tru Power 29X12.5-15 C/6PR (1 Tires) | eBay tires on my Toolcat but keep hearing you have to have the rims for Turf tires need to be used because they are 12.50, what if I have the regular Industrial style skid steer tire rims, are they more...

Does anyone make a conversion from manual bob tach to power, and a Lo flow to Hi Flow conversion kits for Toolcat ?

Looking to buy a used Toolcat, can anyone give me some suggestions on what years to stay away from ? My biggest wants are power dump bed, power quick tach and high flow. Did these come certain year's or were they always options ? Thanks in advance !

My 1045 needs a water pump, does anyone know where to buy one or have it rebuilt. I'm afraid to call Agco, as they probably want like 200 bucks for one.

Drivin my anniversary edition 3240, all of a sudden it stops moving, look in the back and there's abig hole in the rear end where the drain plug is, with a piece of a gear stickin out WTF, never even abused this tractor. Anyone have similar problems, anyone know of some used parts, any advice...

I had this on the MF page, no luck, if this machine is Hino, maybe someone here can help? -------------------------------------------------------------------------------- Drained my hydraulic fluid, replaced new with filters, now 3 point won't lift, book sais the hoses going to loader should...

I was told my 1990 MF 1045 crosses over to a Hinomoto, does anyone know what model, would it be easier for me to get parts thru Hino dealer or MF. Anyone on here familiar with this tractor?

Drained my hydraulic fluid, replaced new with filters, now 3 point won't lift, book sais the hoses going to loader should be hooked together when loader is off, which I removed before fluid change, I tried to start tractor with them disconnected, but would'nt start due to air in lines as I had...

My 1045 has a kinda whining noise, sounds like it's coming from under the seat, kinda like when you open a hydraulic cylinder fully and hold the valve there and then it kinda whines, not real loud, but it's there, and I can't explain it any other way. If you push the clutch pedal down it goes...

Looking at a 1045 with loader 2200 hrs 4wd, how much is it worth and is it a good machine?

Checked out a 2003 Challenger 285 4wd with a loader and 230 hrs. Dealer wants $15,000.00 is this fair, I'm also not locked into the brand, but the size, HP etc. are perfect, can I do better somewhere else, are the 285's a good machine?

Can anyone tell me if a Great Bend 360 loader will fit an Iseki T6500 (White 2-62) 4wd?

My crankcase is full to the top when I check the oil, although I never over-filled. I was told the hydraulic pump/ or pumps mounted on the left side of motor are leaking into crankcase and need new seals or rebuild. Anyone ever hear of this or have this problem before? Thanks

Can anyone tell me if a White 2-62 is indeed an Iseki, what is the hp, weight, where was it made, what kinda motor. Are they any good? Is the 4wd version any good? Thanks