Search results

Hope someone can help. I need the lower beveled gears for the left outboard axle on my 195D. I also need the seal for the pot. Thanks. This problem is a couple of years old , but due to health problems I wasn't able to look after it, and now it's snowing and I need the tractor. LOL. Richard.

Can anyone tell me what the flow volume is for the hydraulics on a 195D? Thanks

I have a case 430, that sat for about 5 months. when I tried to move it the right rear wheel wouldn't turn. Even on towing it stays put. there is a tiny amount of free play front to back when moving it but thaat's all. It wasn't parked with the brake on so I doubt that it is a siezed brake. a...

Anyone have any pics or plans for a receiver mounted electric tailgate lift. I need something to load barrels onto my pickup. R.

I posted the pics of the loader in the original thread as requested. Richard.

I need a starter drive gear for a 1949 Ferguson TE20. It is not the same as the TEA 20. The starter has a nose cone ( like a chev 1/2 ton) and a 1/2" shaft. It is a lucas 6 volt . Also need axle seals for this tractor. Are they the same as the 2N or 8N??? Richard

The Story. When I got this tractor last summer, it had 4 coats of the ugliest paint you ever saw. It was scabbed up like a bad case of psoriasis. Red, Black,White, One layer at a time. I was ashamed to ride it in the daylight. The steering shaft was out of it, the high/low shift lever broken...

A long winter. had to use the blower on 3pt. so it didn't allow much time to work on it but it is finally done. works like a charm. runs at about 700 R.P.M. which works a lot better than it di at 540. Doesn't take nearly as much power on front pto. Here's some pics. Richard.

The loader on my 196d is a ringer for the Yanmar loader shown by Pocono Man in the Rejuv. 276D thread. Mine is labeled KMD Products, Fort Erie Ont. Model K 100. Can anyone tell me anything about this unit. It seems too heavy for my tractor. Thanks Richard.

My YM 195 D has 6-12 tires on the front wheels. I have checked the travel with the rear wheels and it is within 2" on a turn. the manual specs the front tires as 5-14". Can anyone tell me what the circumference of these tires is as compared to the 6-12's. I have wheels in both sizes, so I...

I need a starter for a TE 20 Ferguson. Engine by Standard Motor Co. 6 volt/ 12 volt, whatever I can get. OR a starter drive/drive gear for the original lucas 6volt starter. Thanks Richard.

I have been considering using bio-diesel fuel in my 195D. Anyone have any experience with this?

For those of you who are skeptical about the thermo-start! It has been 10F the last few nights here, I haven't plugged in my 195D and it starts fine. Takes a little extra time on the T.S. and a little slow to fire, but it starts. I only did this to see how well it works. 'Gotta find the...

I see a lot of talk about speeds of 2700 RPM in the forum. This seems to me an excessive speed for my 2 cyl. 195D. Also the limit screw (high speed) has a flattened end with a hole i it like there should be a spring or something attached to it. Can anyone enlighten this old fool??

Under the seat on my 195D there is a valve with a large knob, marked open-close. when I close it it seems to block the flow and load up the pump. Can ayoneone tell me its use?

The old 195D that I recently purchased had no steering when I got it. It appears that the steering box is susceptable to taking in water if it sits outside (although I really don't see why). The previous owner used it in the winter. the steering got really hard so he just reefed on the wheel...

Just to say hello! I'm a new owner of an old YM 195D. I don't see them much in discussions or information and I don't know a lot about it. I have purchased a 51" snowblower for it and am currently trying to front mount it as I have about 1200' of bush driveway to clear and A bad neck so backing...