Search results

Back in business with a new front axle. Total cost of parts and miscellaneous items in the neighborhood of $1000. No cost for labor because I did it all. Edit: I guess I should mention that the axle is an upgraded version of the original. Apparently Kubota had problems with the original...

It is definitely busted. Those two pieces are normally welded together. Would it be OK to get them welded back together or just get a new axle case? Because I'm ignorant, can you tell me what you see that indicates the pinion gear is bad? Which one is the pinion gear and which is the crown...

It appears my front axle is busted.

I need some help. On my Kubota B2400 the front wheels locked up as I was making a tight turn while mowing. I was able to unlock the wheels by backing up and straightening the wheels. Going forward, the front wheels would lock up after about 5 feet of travel. I managed to get the B2400 back...

I was hoping you could help by giving me advice on replacing the o-ring on the front axle seal. I have a repair manual. I understand the axle and the bi-speed unit are together when the front axle is removed. What I need to know is what is the procedure in splitting the axle from the...

Here's some pictures. As you can see I don't have quick attach capability. If you do, make use of it on this project. I added an extra hydraulic valve using power beyond from the loader valve for angling. There was something about the design of my loader valve that prevented the curl circuit...

IMO the problem with a rigidly mounted system is that when you angle the blade one side of the will be higher and the other lower. Thus one side will dig into the ground unless there is some ability for the blade to independently rotate somewhat around the axis that runs through the tractor...

I bought a Western 7 footer for $400. Probably put another $300 o$400 more for new cutting edge, one hydraulic cylinder, paint and iron to build a mount. Around Omaha, rarely is a snow plow priced for sale less than $400.

On mine there is a shear pin and a "C" ring holding the shaft to the mower. In the lower right of this picture, you can see the point where the shaft connects to the mower gearbox. If you look closely you can also see the groove where the "C" ring goes. Looks like I got this posted too late...

Just finished mine up the other day. Thanks to this thread for inspiring me.

AceDeuce, Thanks for the info. When you say bushings what part are you talking about? Can you list the part number from the below diagrams? My parts manual or repair manual do not list any bushings just a bearing and collars. Are you referring to the collars (thrust collars)? BTW, I don't...

My B2400 has a small leak. It appears to be coming from the front axle holder. Looking at the parts diagram, I don't see any seals, just a collar and o-ring. Does anyone have any experience with this? Would replacing just the o-ring stop the leak or are there other internal parts that need to be...

Last week, I bought a Western 60125 seven foot snow plow to attach to my B2400. Attached are some photos of the plow and the mount I made. I plan to prime, paint, and add hydraulics. Cost of the plow was $300.

B2400 leak from clutch shaft seal. Help. Photo added. I have a b2400hsd I think it has a hydraulic leak from the seal where the shaft enters the clutch housing. Has anyone replaced this seal? What does it entailed? The access appears limited from the bottom but it looks like it might be...

On my b2400 the fuel cap tightens down then pops loose. I replaced the fuel cap once before because of the same problem. I've been very careful about over tightening because it cost about $30 to replace. Seemed expensive for a plastic cap. Anyway this seems like a stupid question but here...

I'm leaking hydraulic fluid right where a hydraulic line enters the steering component. A minute crack in the flare is the cause. This is the third time I've replaced this line for the same reason. Is this a common problem? This is a 1996 B2400 hsd.

Anyone install a block heater on a b2400? Does it go in engine block just above the water line return replacing part 050 in attached pdf file? Anything else of which I should be aware? Thanks tomf

I started my B2400 up in cold weather, about 0 degrees F. I was letting it warm up. I went in for some coffee. Upon my return the tractor was not running and there was hydraulic fluid all over the ground. Lying on the ground there was a 1.5 inch circular rubber seal/cover/plug. It came from...

Does anyone know what this is? What's it's function? If fell out of a valve port when I was removing some connectors from the valve? Thanks Tom

I recently added a front blade to my loader using a Sauer Danfoss 1618-AL valve. Information on the valve can be found here on page 27 http://www.sauer-danfoss.com/stellent/groups/publications/documents/product_literature/520l0564.pdf The valve controls the blade fine but when the valve...

I have a b2400 with LA352 loader with a Husco 9210 2-spool valve. The spool that controls the loader arm has a float position. I'd like to use the float position with the cylinders that control the bucket. So I switched the hydraulic lines going into the work ports. I expected the controls...

Does anyone know where I can get a power beyond sleeve for a Danfloss Fluid Power 1618AL valve? Or where I can get a handle for it. Thanks Tom

Does anyone have any ideas on whether or not it is wise to plumb another valve to a FEL valve? I'm planning on attaching a snow blade to my FEL. I need another valve to angle the blade. I was thinking the easiest thing to do would be just to add another valve downstream via the FEL power...

I'm losing oil from my mower gear box. I'm guessing one of the seals has gone bad. Do the seals just pull out and then the new one is pushed back in? Is there a special tool required to extract them? Thanks Tom

My B2400 starts and then immediately stalls after running one or two seconds. When it stops it sounds like a normal shutdown. When the throttle is in different positions the engine revs up appropriate to the throttle position. Started and ran perfectly about a week ago. I cleaned the fuel...

Can anyone tell me how to remove the spring pin from the hand throttle on a kubota B2400? I have the service manual which says to "tap" it out. But the spring pin appears to wedged in too tightly. Do I need a special tool or what? Thanks for any help. Tom