Search results

I'm considering a new (to me) finish mower for my property. I see many of the commercial operators running Walkers in this area. I've heard good things mostly about them. Some bad from others, does anyone here have one (or more) and what do you think??

Would any one care to discuss the differences between these two units? Are there differences in them aside from the cosmetics and chassis size? Maybe some technical information would be nice. I'm looking for a diesel zero turn with a 54-60" deck. Pretty much sold on Kubota...

I am looking at buying a used M&W Zero Turn, model LC183D-II. It has a small diesel (I'm told ~18hp Perkins) and a 62" deck. No price has been set, yet. It currently has a broken (plastic) cooling fan, but is in otherwise good shape. Does anyone know anything about these or have any...

My neighbor just bought one of these (IH 2544). Nice older ('72), Industrial, hydro tractor with a loader. Problem is there is not 3 point on it. Does anyone know where to find one of these or has someone fabbed on up for something similar? Thanks.

Okay, I'm looking for something to use on the property to run around. For the wife to go from the barn to the garden, mailbox runs, garbage detail, etc, etc. What do you think of something like this? I'd love a Rhino or Mule or something like that but the $2500 for this is alot better than...

My new L3400DT is on the way. Thanks for the input weather you added to the thread or posted years ago that I found using searches. Thanks. To the L34xx owners out there: What size rough cut mower, box blade and finish mower would you recommend or have you used with good or bad results. I...

Okay guys, I've made the decision to go with an L over the B7800. Can anyone please give me some feedback on these prices: L2800 HYD - 13,242 L3400 DT - 13,025 L3400 HYD - 14,393 LA463 (60") - 3,272 I'm thinking the L3400 DT (gear) with the FEL. Thoughts or comments, please!

To all the B7800 owners out there, what other models did you compare it to before you bought? JD, NH, other? Thanks

After bending one, and breaking the other tensioner chain on the 3pt on my BX2230, I did the B7610 modification. Can anyone who has also done this mod tell me what type of pins they use for the adjuster? I slotted the lower hole for the factory clevis, and used the pin from the upper factory...

I thought I'd bring this subject back up again, because I was able to see the OEM BX cab today at the dealer. Without a doubt it is a very nice cab. The one they had there had a fully insulated CARPETED liner across the fenders, under the seat and a thicker pad on the floor. The heater...

Tomorrow is my last full day here at the university. I will unplug from the T1 for the last time, then it's off to my home and the land of dial-up. I'd just like to thank everyone here at TBN for being a "reality check" against the land of institutionalized insanity here at college. I...

I thought I'd make a brief post on my impressions on a first drive of a Jeep Liberty CRD. I drove a Limited level CRD. The trim and vehicle in general is the same as a gas version, so I won't waste time on that. The Motor started with a few seconds of wait with a small white puff. (45°...

Back to the original topic. Would someone take a picture of themselves running the BX22/23 hoe or the BX2200/2230 with the Woods hoe so we can all see how the ROPS interference issue is or isn't an issue. In specific: I would like to see a body sitting on a tractor while operating the Hoe...

Now that there are a few of them out there running, I have a question for those lucky operators: How is the seating position, especially in relation to the ROPS? I'm wondering if the lower ROPS of the non-BX22/23 is a head banger. How about the leg room over the back of the tractor and the...

I've been watching a thread about the fuel prices here in America and the question was raised: Have the fuel prices increased dramatically in Europe lately? Being the only active European poster that I can think of, what do you know about your prices and the prices across the channel from you...

Where ya been? You've been missed badly.

Does anyone know of a good, active aviation forum along the lines of TBN out there?

My only project for the day yesterday was to do the 50 hour service on my BX2230. The job was not difficult or strenuous, but please allow me to make a few comments. 1.) Changing the motor oil with a snowblower attached: not smart. The driveline is directly under the drain plug. Kind of...

I found this for $19.95. Unfortunately it came from the JD dealer who wouldn't quote me a price on a 2210 when I was tractor shopping. (Long story I'd rather not get into. He told me to my face I was a "Looky Loo" because I asked too many questions.) I hated to even give them $20, but...

I know this one has to be out there somewhere, but my searching hadn't found it. Does anyone have a TnT setup on their Kubota BX? Who did you get it from or did you build it yourself? Do you have any pictures of it? Do you have and general thoughts about its function on a small tractor like...

Does anyone have one of these setups on their B or BX Kubota? Before I spend $70 on a new top link (mine is bent, don't ask...), I would rather invest in a hydro TnT. These look like a fairly complete kit. I would appreciate any input on this. Rankin web page

Has anyone had a failure of the float detent on their LA211 FEL 4-way valve? I have a BX2230 with the "new style" 4-way valve. I just had the valve repaired under warranty to repair the float position not holding. I had been Parking the tractor with the control in the float position. Is...

There have been several posts showing pictures of cabs on BX Kubotas. I have not been able to find any showing the Curtis "Hard-sided" cabs. I am considering a cab for my BX, and so far I am leaning toward the Sims, but I would like to see what a Curtis hard cab looks like, too. Does anyone...