Search results

Put this in wrong place. Mods feel free to move to owning operating.... This one was my first actual problem and it was for a little bit dangerous because of when it occurred. Its avoidable too. I waited to post this until I had a complete outcome of the issue. I do not know what models this...

Kind of funny in a way. When my 2610 was delivered the headlights did not work. It had blow the fuse. I tried a new fuse and it blew immediately so I just stopped and called. We discussed this over the phone that next day and we decided to wait until it came back in for its 50 hour service...

If you had it down to those two used ones and all things model wise are about equal which would you chose? Are they about equal in quality and parts availability? These both would be the lighter duty entry level models. I tend to sort of lean to the Land Pride for some reason I just cannot...

Ive been cutting about 5 acres with my Toro zero turn. But I also do a lot of finish type mowing on trails and have about another 3 acres I would finish type cut if I could. Im tending about 19 acres of pastures and a little woods and creek edges. Hilly stuff. Some open slopes but not much of it...

I need a good picture of diagram (both even) of where the Power Beyond port is on the 2610 HST. Anyone got one or can take one? I think its located under the seat. But I need to know which line into the valve is the Power Beyond one to tie into it for a third function install. I am debating...

True third function plus 60" grapple installed $2200.00 OTD Reasonable? Fair? Im being told the Grapple is $1000 of that. Which rings true from my research. I just have no concept of the Hydraulic third function part of the cost. Photos are of the same parts as quoted to me that were being...

And if so what did you get? Looking at something like this for gardening chores to pair with my Tiller attachment King Kutter Sub-Soiler, Model# SUB | Category 1 Cultivators Tillers| Northern Tool + Equipment

I was digging around some old equipment left over here from our old Ford 5030. Trying to decide what I can use and what to sell or trade off for what I need. And I dug what I thought was a 9 tine Cultivator out of the honeysuckle and discovered it was a Fred Cane Cultivator Ripper instead. I was...

Need a normal check here I guess. Had this thing a week. Got the crash course on these turnbuckle stabilizers so thats now up to speed. But three things I notice that I need to get input on. I've put about 6 hours on it. It shows 10.2 hours total. 1) White smoke on initial start up. Gone in...

Just got this thing and this is how the dealer dropped it off. Certainly those gold colored adjustable bars that are attached to the lift arms do not just lay there and flop around. Certainly they are to fasten somewhere but I do not see it. There is one link of chain one the right one and a U...

Need input on a Diesel \"in bed\" fuel tank setup Cannot really find a right place here for this but figure you construction guys will have more experience with this than most. And a Moderator will move it if I got the wrong place. Ok help me out here. Designing one of these for my Biodeisel...

Anyone own one of these for any length of time? These were highly recomended by a Neighbor/Small engine repair shop owner/ fellow Gardener. And recently the Father in law is sort of shopping around for a replacement. He likes my little Troy Bilt Pony but wants something bigger. And needs...

After about 5 hours time on this thing...I am reading this operators manual.... yea... realy! Says "For engines without a shutdown solenoid: move throttle to slow or low idle position. Allow the engine to idle for 30-60 seconds; then stop the engine. For engines with a shutdown solenoid...

I can\'t leave nothing stock.... ... I just gotta drill holes in something new.... nothing like the "pucker factor" of taking a drill to a new mower and adding something. In this case some lights. Who needs lights on a mower anyway? I dunno.... but I kinda like the dune buggy look it got from...

Be gentle... its my first time.... ZTR\'s again. Hey folks. Been doing a lot of reading here. Got a good baseline of information from here. So thanks for that. My story? Well.... my dear beloved Snapper LT is about on its last legs. Over 23 years of faithfull service. Still rock solid body...