Search results

I'll be running a bush hog on my BX22 in the next few days cutting some pretty tall grass. I've been running the clipper on a B7300 but the pto clutch started slipping last year and I dont think it will make it through this year. My clipper is a Bush Hog brand 42" Squealer. My question is...

Short of pulling the transaxle, is there a way of inspecting what might be in the bottom of the differential housing? Pieces of gears, the differential lock etc? While operating the tractor this weekend I had earlier used the differential lock and while I was in a turn I heard a pop that...

I've got a BX22 with 1200+ hours on it. Today while using the FEL I noticed that it was leaking down while it had a load on it with the engine RPMs up at operating speed. I had gotten off the tractor to move something and noticed it leaking down when getting back on. I've looked all over...

Does anyone have the instructions for "Tweaking" the POS W-Pins for the BXpanded Q/A Forks and bucket hooks. I lost the instructions that were sent. My pins are totally worthless. If anyone knows of something better to hold the Q/A to the bucket short of welding it on I'd like to know it.

Some of you may remember when I posted several months back about a used Bush Hog Sq142 I bought. This past weekend was the first time I've used it to do clipping with. I must say the B7300 with the little Bush Hog is a really good match. I was really impressed with how well it performed. The...

Does anyone know of a salvage source for Kubota parts?

Does anyone have any experience with Bxpanded forks? I've been using some homemade bolt on forks that have broken and welded several times and I'm ready for something different. All comments good and bad appreciated. Thanks

All, I came across a smaller 42" rotary cutter that appears to be in excellent shape. I'm not sure of the age but the metal decking and sides are not beat up or rusted at all. There doesn't appear to be any leakage of the gear box where pto shaft connects. At the time I couldn't look underneath...

I'm slowly but surely getting the leaks fixed on this tractor.....Has anyone replaced the orings on a B7300 pivot on the front axle. I tightened the pivot bolt per the owners manual instructions hoping that might help and the leak slowed down but is still leaking. I've replaced the UDT in the...

The mid-pto is leaking and it appears to be coming from the seam where it bolts to the transmission not the shaft seal. In looking at the parts list for the mid-pto and the transmission I don't see a gasket or o-ring listed for where the mid-pto assembly mates to the transmission. Is it just a...

I have a B7300 with a D722 engine. It has 2128 hours on it. It was leaking fuel from the top of the injector pump from under the plunger flanges. Following the post here that "You CAN repair an injector pump" I replaced the orings on the plungers. After putting everything back together, bleeding...

Has anyone removed the main pin pivot pin at the bottom of the boom? One of the dipper stick cylinder hoses has developed a leak. At least I hope its a hose....I was wondering if there are any words of wisdom or gotcha's that anyone that has done this before may have. If its a hose I plan on...

The mower deck height control knob is missing from my tractor so I've no clue where the top lock setting should be. The rod that the knob was on turns easily. My question is... which direction do I turn the rod to raise and lock the MMM arms at their top most setting? The owners manual doesnt...

I have the shaft out of my tractor to replace the HST fan, CV boots and both joints. In looking at the parts diagram of the CV joint, it shows O-ring dampeners under each ball in the joint. The joints on this tractor are the original joints with 1300+ hours of run time and I have no clue how...

In looking at both plates on their respective sites, I'm not sure which to go with. Bro-Tek requires two separate plates to get full coverage but has an access door for Mid PTO which I'll probably never use. Living in central Mississippi there will be no need for a snow machine attachment and I...

Now that the weather has started to cool off down here I've started doing things to the BX22 that was left to me by my neighbor that passed away. Some here may remember my "BX22 Left To Me" thread. So far I've put a new seat on, changed the front end oil over to 80/90 weight grease, tightened...

All, I'm in the process, as time allows, of rejuvenating the BX22 that was left to me a couple years ago. Yesterday afternoon I changed the front axle oil over to 80/90 weight grease and tightened the axle pivot castle nut. The castle nut was quite loose. The capacity of the front axle is listed...

With the ease of which the plastic HST cooling fans get broken and the H3LL you have to hug to replace them, I'm wondering if an automatic transmission cooler placed in front of the radiator so the fan would pull air through it would work. Is it even possible to plumb one up? Would it cool the...

Not sure if I've posted this before or not. I did a search and couldnt find it if I had...... A dear friend passed away this past November and in his will he left the little tractor and all implements to me. Here are a few pics of the tractor and implements. I havent done any thing to the...