Search results

Hi, I have an old JD 1020. Which now days I sudenly had quite big brake and I pushed in the second speed (Hi), starting that moment - the gaerbox os blocking frequently, is hard to change the speeds, one of the speeds mainly the second one - is not working well. Its seems to me if the switch...

c

Hello... Today we removed the tractor front axle. As I see a lot of pieces are overused / bushes, washers, pin, bellcrank-pin... I try to buy same new pieces / as bellcrank AR53392, or only stearing arm pin, as you can see in the photos.. We also buy needle bearing, but the problem is that...

Hi, I checked again the tractors docs, I found that is dated from 1975 / or at least the end of year 1974. i dont understand / according to the Tractordata.com page, the 1020 type was made only till 1974... Then, whick information is the right one? Thanks, Benedek J.

I find...in the tractor front... 166413L

You have right... I will check it... I live in Romania, but I am hungarian... I understand Englush but I cant speak... Here also lived germans.. . Transylvania, Siebenbürger... My grandgrandfather worked in USA, between 1909 and 1928, in Detroit, but he returned. We have relatíve in USA

I have the original tractors papers from Germany (register, stud book).

Thanks.. On my tractor I cant see the serial number plate.. But its made in 1972, theoratically the serial number sholud be starting from the number 134700.... Am I right_?! According to your advice I need to buy the needle bearing?

Hi, I have a new problem with a stering arm from the front axle as you can see on the attached short video. The triangle shaped bellcrank is clicking very much on its own hole/caliber. What could I do? I suppose I should repair/replace the bush between the stearing arm pin and the caliber/ or...

What is should be the proper oil pressure on the gauge?

TxJIm also adviced us to check the same thing...

Hi, I search for this # AL57974, but I only found the lift cover gasket, like in photo - not the control valve seals...

O.K., I understand... Maybe -the big piston sealing are used (AR33105)? Or, we have to replace all seals on the piston and at valves.........?! DOES exist any repair kit for the valves? If not, what should be replaced from those little pieces from the valve diagramm? Only the O-rings_?

Thanks, As I see, we have a multiple type of problems. What should be do?! Where do I find this control valve - to replace seals? I checked on a few diagrams, but I could not to identify it... Probably that the oil pump is not guilty for the problems, should we forget for now the pump...

Hi, The suction screen was checked and cleaned, the relief valve not yet, but they will verify it... I found something new: ex. in morning, in cold, when the engine, the tractor body is cold - the lifting works perfectly... But, when it gets warmer, the lifting is weakens and finally, does not...

Hi, TxJim... The problem is that - the tractor hydraulic does not lift, in the backside... Soo, it does not have enough oil pressure. This is one of my friends tractor, my own is JD 1020. He replaced all of the filters, changed the hyd oil with JD HyGuard, changed the little pump in the...

Hi... There is a JD 1640, 4x4, from 1982, serial number: 428793... Now, I am looking for a new hydraulic pump... but I am confused. The tractor is made in Europe, I suppose it is not made in Spain... In my research, I found two types of pumps: with 23 CM2/min (1,4 Cu.Inch) flow (AR103036, AR...

Hi, I have quite a lot of problems.... I put in the O-ring to there location, after that warmed the Teflon ring in hot water, but I did not really manage to put it in.... After trying more times, the ring was damaged.... Finally, I put the other ring, inserted the new shaft / soo one side is...

Hello, Jim. I started to fix the oil leakage problem... as you can see on the attached photos. I bought original pieces, O-rings and teflon washers, but I would like to ask something.. 1. I desassambled everything, but there is a piece - which is marked with red arrow on the photos - is...

Hi, I got the O-rings for the oil flow control valve.... So if I remove the three screews (8,15 and 16 from the photo), and I change the O-rings, replace the screews and the job is made with it_?! Is there any possibility to fall of any other pieces as the 3,4 from the photo?!

Hi, I have a question: I refilled the missing hyd oil level (JD Hy-Gard oil) with Triax Tractor Fluid Oil...... Did I do a good thing? I hope within a few days I will received the new set of O-rings for the oil flow control valve and the leaking will stop.....:confused3:

Finally, I identifyed the mentioned piece, is the flow control valve - R39273... After the pictures, it does not exist any special gasket, there are only two O-rings: a bigger one (the yellow one) and a small one, as you can see on the attached picture... The problem is, that I am not able to...

Hi, I have a new problem..... Under the tractor, behind the hydraulic oil filter case there is a piece, as show on the attached pictures... And from that piece the hyd oil is leak... But in the JD catalog parts I dont find this pieces name in english... and thats why I dont know what type of...

Hi..... the screen is located behind the hyd oil filter case - as you can see on the attached photo.. Other schemes: Or - it is possible that the oil transpump is not working well and from this reason the frontal principal oil pump is not getting enough oil..... Do you have enough hyd oil...

Hi, JIm Finally - I found what the problem was caused by...................... The T25325 piston and the T25323 rod are assembled with screw thread................AND this screw thread sometime broke as I can see on the attached pictures.... Look at one original new piece and my broken...

I have a question:what is the function of the shims from the steering column - with these codes - T25741, T22825 and T31290 -? I observed that they have different diametres - are they serving the calibration or do they have other similiar function?! Totally there are 6 pieces / 3 pieces for...

Hello, JIm... You had right - the valves on both steering control unit (AL26312 and AL26311) is stuck..... Verry tightly... I dont understand why did it became both so tightly.... The end of the shift almost curbed..

Hi everybody... I removed the water pump and I am going to disamble it... Which part should I start, what is the right order to disamble?! First, I think should I remove the T30720 hub from the axle? But how, with hyd press because with bearing puller is not working...

Hi, Could you please look from the code of the thick rings from the pictures - I tried but I could not idebtify them correctly from the online JD part catalog--- Thanks, B.J.

So the plunger must move freely and easily... If I put on it screw losening or the graphitic spray I suppose that it is going to work fine. On the attached photos it can be seen a deformed slim rings - is this a big problem?! What makes it to operate these valves when I rotate the wheel - ?

Hi, Tx Jim... Today we dissambled the PS valve housing, I will attach some pictures. Now I see that all the 6 O-rings are situated inside the housing. When I will get the new PS repair kit, I am going to change wich is not going to be an easy operation. Do I see correctlly that all rings are...

The first number is T25285...and the second # is T28388.... The seller told me that according to the catalog, this stering valve must be right for my JD1020. And hi has really right - every screw, caliber, the oil pipe join, gaskets a.s.o all are fitting perfectlly. The bottom sequence is...

Hi, JIm. Today I repplaced the PS column.... Now I have a longer PS column, but its not really working... I drived after changing it. It seems to me that sometimes it is working and sometimes not. I also tried the 3point lifting - it works, but sometimes responds to...

T25285 and T29389...

Hi... I found an used PS unit, but there are some problems related to it.... First - it is too long, its longer than the original one, aproximatelly with 8 inch... Secondly - the bottom part is missing.... What should I do? I think I try to fix it at its place...

The transmission pump - AR96662 - where can you find an the tractor, backside, on the transfer case? And what is its function - does press oil for the transfer lubrication, or is it feeding with oil the high pressure pump in the front, or what?!

I dont understand something which may be important for the working of the hydraulic. Its about the cover which can be seen on the picture. Piece nr. 3 from the scheme is gasket, on it there is a rectangular hole. When I removed, this hole and under the hole the calliber was also filled with red...

Thanks.. This morning I tried to lift with cool hyd oil - it was working a littke bit better than with warm or hot hyd oil, but it is not good at all. I already checked the oil level - its good. If the steering O-rings leaked, than if I close the pipe which goes to the PS (photo 2), than the...

Are you refering to the pieces from the attached photos?! And the part key 3 / the gasket - why is....against the oil-escape or against only the powder.... There cant be oil pression - thats whay I ask about this.... Tomorrow I will dissassemble that cover..... The...

First, after this, I believed that you saved me unnecessary acquisition.... Please, take a look on the each photo, on which you will see the base of both pieces, with joins/pivots.... It is almost totally sure that the second hand piece is really a manual sterring, without oil...

Hi, the hose is attched the bottom with the header pipe which comes from the hyd pump.... Originally, the hose is a steel pipe which broke and I replaced it with a flexible new rubber hose... the original can be seen on the photos....

Hi...new photos..

If enlarged this photo..can see the Hy Press Oil pipe....

Thank you for answering so soon.... I was ploughing and the tractor's wheel crashed with a big stone...and the PS failed...after that is working only rarelly and it work only manual and hardly... I have some questions related with the attached photos: -first, the PS repairing kit is it...

Hi, on my JD 1020, the power steering mechanism failed........ What can I do ........ can be fixed with the AT26188 John Deere Power Steering Column Seal Kit or needs to be change with an other used piece???? The piece part numbers, AL31262, AT26188...

No lever... only PTO ON/OFF switch lever on the tractor'"s gearbox left side............... If you watch the following video as I also did you will see that the tractor JD 1020 made in 1966 has PTO/engage lever.... But my tractor made in 1975 does not have PTO lever between shifters... Then...

Hi... I have a JD 1020 tractor .... When I try to shift on the PTO, not responding.... I tryed with the depressed clutch pedal - nothing, with undepressed clutch---- nothing...:confused: Please, help me.... If you want, I tryied to sending video .... Sorry...