Search results

I am going to Buy a new JD 1025R with a loader. I currently have a king Kutter finish mower and had planned to use it since the cost of adding a belly mower was so high. I have found the belly mowers at another John Deere dealer for 1849.00 with hardware. My question is how hard is the...

I have a King Kutter FM60 which has only been used twice. It has already shelled a bearing in one of the spindles. I ordered a bearing set online but they were typical Chinese bearings and they did not look to be very high quality. I went to my local Fleck Bearing company and had them match...

I just picked up a finish mower and have never seen this PTO coupling before. The collar does not move as far as I can tell so I am not sure how it locks on or unlocks from the tractor. I am hoping that someone out there can tell me how this works. Thanks, Gary

I just picked up a brand new King Kutter FM 60 finish mower at a sale. It has never been used and was shipped dry from the manufacturer. I am not sure how much gear oil to put in it. I don't want to overfill it as well. Can anybody educate me on this. Thanks, Gary

I checked my hydraulic level this weekend and discovered I had water in the fluid. I realized that my shifter boot had a huge split in it and we had some heavy rain this week. I replaced the boot but snapped the treaded stud off of the end of my shift lever while trying to get the knob off...

After much searching for replacement headlight bulbs for my ford 1510. I finally found the source. I had priced them at the dealer for 17.50 each plus tax and shipping and was shocked at the price. I finally looked at the fine print on the bulb which in my case was "Stanley 12V35/35W" I...

I am going to go ahead and add a temperature gauge to my 1510. I would like to keep the idiot light operational as well. Is there another location on the motor where I can add the sending unit for this gauge and leave my idiot light in place? Any help from the gurus on this site is greatly...

Does anyone out there know where I might find a used or salvage ROPS for my 1510? It did not come with one but I would sure like to have it there. Thanks, Gary

I recently had to replace a lower line and decided to changed the hydraulic fluid in my Ford 1510. I put 19 quarts of fluid in as recommended by others on this forum and my data. However it did not register on the dipstick. So I added the remaining quart left in the 5 gallon bucket and it...

I changed a hydraulic line on my 1510 this weekend and had a couple of questions. First, I looked in the manual and there are three drain plugs shown. One in the middle of the front of the transmission and two in the rear axles. I drained the front and when I took out the rear plugs nothing...

I have to replace a hydraulic line on my 1510 and thought that I would change the fluid while I am at it. I found tractor hydraulic & transmission fluid at NAPA that is rated for New Holland/ford M2C 134 A, B, C. I know that it uses Ford 134 rated fluid. Will this work? It is NAPA 85-475

Ok, I feel dumb asking but......here goes. I just bought a ford 1510 and am getting to know her. There is a petal on the right side under the seat, directly behind the brake petal. Can someone tell me what it does. I brush hogged with the tractor last week and just noticed the petal...

I recently replaced my old 9N with a Ford 1510. When I hooked up the brush hog the front wheels tend to come of the ground sometimes. It has a bar on the front and I am looking for suitcase weights. The question is how much weight do I need? When the front does come up it floats slowly and...

I want to put a temperature gauge on my 1510. I don't trust the idiot light. Does anyone know where to find one that will mount on the tractor externally. There is no place (hole) in the dash for a temp gauge so it will have to be mounted on top. Thanks, Gary

After 10 years of good use from my 9N (still runs great by the way) I just bought a Ford 1510. I am looking forward to interacting with the pros here as I am sure that I will need advise. This is my first Diesel and I have a lot to learn.