Search results

I have, I知 assuming a ford brush mower. Because its blue. I cant find any numbers or names on it so not sure. I am in search for new blades for it. One has broke and I can稚 find any new ones anywhere. They are a straight blade reversible cutting edge 19 7/8 long 3 inches wide with a 1 hole any...

my buddy rented a tree spade and in the process of moving it into position he wacked the remote unit and pulled a bunch of wires off. he has 3 yellow wire and a black wire without a home. He thinks he got the red and black wire where they belong but I am not so sure. He can lower each spade...

I hope I am asking this in the right location. Is there a way to look at the scag zero turns like the wildcat, turf tiger mowers serial number to determine what year it is? Been looking around at used one and some say they are only couple years old and they look like antiques rusty and faded...

My tractor/mower is eating mower drive belts and I cant figure out why. I usaually use this mower for tilling only but my other mower blew the engine so I put the deck on it and have been mowing, randomly though it chews up the belt. I set the spring tension per the instructions. I put a 5/8...

I went out today to drag some dirt around and when I went to lift the box scrapper on the 3 pt it wouldn't lift, nothing not even a whine or engine rpm change. Can someone direct me in the right direction on what to check first then on down to try and figure out whats going on. I did a little...

Has anyone adjusted the forward speed of one of these mowers? I have borrowed one from my father in law and it seems that the forward speed could be a little faster. There is a lot of wasted motion (slack) in the forward/reverse lever I push the lever forward to the stop and it seems like it...

Was mowing with my old worn high hour mower yesterday when it made a clunk noise and started vibrating bad and loss power. I got this mower a few years back and the hour meter is broke at 1700 hrs, Used a lot of oil and was very weak in taller grass, anyway I puled the the head today and it...

I have this valve https://www.surpluscenter.com/item.asp?UID=2232010700071954&item=9-7724&catname=hydraulic 1) is it best to have the ram bottom out in the return position thus causing the detent to center the valve or have it stop short a little bit by installing a bolt or something so that...

This may have been posted before but I just found out about so I thought I would pass this very important message along. Brake clean when heated say while welding will emit a very dangerous gas here is the link Brake Cleaner = Phosgene Article I use brake clean all the time and easy could have...

I am going to attach a wood splitter to my ingersoll lawn tractor that has a valve already in place that has a manual locking device that will lock on the hydraulics for the tiller. I plan on using this to power my wood splitter, so I will lock it in position and run it to and through the...

I have a 24" cylinder and I am in the mock up stage and I am wondering the pros and cons of setting it up so that I get full travel all the way to the splitting edge. Should I make it so that I have room for wear on the edge and make it so that the ram bottoms out with say a 1/2" more travel or...

I am building a wood splitter to run off the hydraulics of the tractor What type fluid can I use in place of the "Ingersoll custom blend motor oil, this oil is custom blend for hydraulic applications" taken right from the manual. I have no idea where to buy ingersoll special blend motor oil...

I have a valve that I want to use for a log splitter that I am putting together. Its a cessna valve and I am sorry I am at work and cant remember the exact number but it is something like 3051-12c I know the first part is not right but am positive that the 12c is correct, is there a chance that...

I have 2 different beams that I want to make a log splitter rail out of, tell me which one would be the stronger first is a 6x6x1/4 meaning it is 6" wide on the flats and the middle riser is 6" tall but its only a 1/4 thick or a 4"x 6 1/2"x 3/8" thick this may be my choice because it is 6'...

I am gathering material to make a log splitter for my father in law that he can use with his ingersoll tractors hydraulics. It has a mounted valve on the back that operates the hydraulic tiller and other implements. My question is how would I use the valve that's there and also use a hand valve...

When I raise the bucket on my uniloader it will drop before it raises. As I first start to move the lever up it lowers and if I keep it right at that spot it will lower completely down until I move the lever past that spot. Anyone know if this is a adjustment problem or a worn out part problem...

I have a 1974 I think uniloader and I would like to know if anybody might be able to help me. When I got to raise the bucket it right at the first part of raising it, it will drop until I reach a certain part of moving the lever which means I have to move the lever farther to get past this spot...

I have a mower deck on my 420 that needs maintance. I just left the JD shop and they are scary high on bearing replacements. So does anyone have the bearing cross reference for the blade spindles? I am hoping the gear box on the deck isnt damaged but I am afraid that it is. My son managed to run...

I have a onan 20hp gas engine and am wondering what the cyclinder compression should be? Hour meter states 600 hours but I bet its double that. reason for the question is that I am loosing oil and smoking through the ocv type vent on the dop of the engine, and am wonder if it is excessivie blow...

I have a JD420 Garden type tractor/mower The engine is a onan 20 hp and just started tonight blow ALOT of oil out the vent in the top of the engine that goes into the air filter. I am assuming this is blow by from the crank case. My question is if there is a equal to this engine in the kohler...

I have a 420 lawn tractor and I am having a issue with the govenor I think. It pulses preety bad at low rpm, like the govenor is messing up so I thought I would see about the ajustment procedure and check to see if it is adjusted right, although I do suspect the carb is out of adjustment a...

Is there a trick to getting the plow to plow deep, well what I need to do is trench as deep as trench as I can with it. Do I need to angle the head any certain angle or just straight up plum with the world? I am going to use it to run underground wire about 650 feet and I want it to go as deep...

Is there a trick to getting the plow to plow deep, well what I need to do is trench as deep as trench as I can with it. Do I need to angle the head any certain angle or just straight up plum with the world? I am going to use it to run underground wire about 650 feet and I want it to go as deep...

I am considering running a air line down to my pond, about 700 feet so that I can aerate it, some people have used a middle buster plow to trench a 6-8 inch ditch to lay the air line in and said a 55hp tractor did it with no problem, ( per pondboss.com forum ) I am wondering if my 22hp 226d...

I noticed the other day while mowing brush that my tractor turned way sharper to the left than it did to the right, Where should I begin looking for adjustments or is this normal?

I am considering the idea of a fel on my tractor and am curious what it looks like with everything attached to it and where everything hooks up at...Does anyone have a picture that they could post..I searched and found some nice post of fel information but I didn't catch any pictures..I have...

I have a JD 420 lawn tractor with a oil light gremlin, it seems that for no reason every once in awhile the oil light will come on and then go off after I hit a bump or something like that. I have checked the oil on these occasions to see if it was low and never is. So where is the oil sending...

what is it for? It starts and wraps around under the seat then ties in back close to where it started, why does it have a long wrap around hose when it could just have a short 1 foot loop. I never noticed it until it was hanging real low and I was concerned about snagging it on something.

I have received great information and contacted the venders for my parts and will purchase my parts, but I hate to be a parts changer to see if that fixes the problem, so my question is how do I check my altenator and voltage regulator ? I have a couple different fluke meters to work with. No...

YM226D tires Is there a replacement ag type tire for a 25x8.5x14 tire that wont break the bank? I found a source for tires on the back 13.6x16 turf type was the only thing I could find for the rear..There is a place in Shawne Kansas (near KC.MO.) called tire town(www.tiretown.com) I picked up...

I have a jd420 gas engine that just started this problem. When I hit the pto seitch for it to start the mower deck it comes right on the runs for about 10 seconds then dies , Then I let the mower deck come to a halt then reset the key and it will start up then run for 10 seconds then die. If I...

Hello. Brand new to the forums as I am a brand new tractor owner and I have questions please bare wih my lack of knowledge. I just purchased a nice tractor and I am going through the maintance procedure for it because the previous owner didnt up keep it. I have changed the oil and fluids and...