Search results

All is running fine.

I ordered some Loctite N-5000. I'll experiment with it and see if it works or gets blown out by the gases.

That Permatex product isn't ideal for my purpose, as I want to be able to unscrew the muffler in the future, if necessary. I'm still leaning toward the anti-seize, but I'd appreciate knowing people's experiences with both the copper and nickel, so I can choose between the two.

If I just leave it, the gases escaping out of that crack will eventually eat away at the pipe, and that will only lead to more headaches. I'd rather prevent the damage rather than just live with it. As far as furnace or exhaust cement, that's what the anti-seize is for... unless you've used a...

I have a Mighty Mac 14PT that works great. I only wish I ended up with more mulch after shredding a huge pile of branches. I recently noticed an air leak just below the muffler. Though I couldn't tell if it was leaking on the top or bottom of the pipe the muffler is attached to, I sense it was...

I have it all back together again, other than the muffler, as I didn't realize till I tore it apart that the gasket was destroyed. As soon as the gasket arrives, I'll see how it runs. Everything looks beautiful. While I was at it, I refurbished the recoil starter and replaced the two bearings in...

Thank you for your response. After disassembling and soaking the fuel tank shutoff valve in alcohol, fuel flows freely to the carburetor, but the engine still runs rough. I just got a can of Berryman 0996 Chem-Dip, and I plan to disassemble and soak the carburetor in that. I don't have access to...

I can blow through the line, and there is no restriction. The only restriction seems to be in the filter assembly section of the fuel shutoff valve. I just found it strange to see how little fuel gets to the carburetor. Fully choked, the engine seems to get more fuel, but it motorboats, with the...

I've been attempting to get my tiller running, but I'm having trouble. The engine runs rough and then dies, and it must be kept with the choke on to run at all. I cleaned the jets, but that didn't help. When I removed the air filter, I could get it to run smoothly for awhile. I thought maybe the...

I have an old Amerind MacKissic Mighty Mac Shredder. Two of my four tires are shot, and I am replacing them with new ones. The original tires are ribbed, but I will be replacing the two bad ones with knobby tires. I move this machine around with my BCS735, so there is no power to any of the...

Where do you recommend putting the moly grease?

As I stated above, this is an Acme Motori ALN330wb engine. The owner's manual states this: Even they don't recommend taking it apart, but I was just checking to see if anyone has a trick for doing this (for cleaning purposes).

What my recoil starter looks like

I tore apart this recoil starter to see what I have. I avoided removing the spring, as I can't see an easy way to reinstall it. If any of you have taken out the reel with cable and spring, please share how this is done. I sprayed brake cleaner down inside until it ran out clean. As you can...

Apparently, Acme can't figure out the correct spark plug for this machine. Is the Champion L86 or L90 to be used? They seem to be reversed in these two Acme publications. Which is for gasoline and which is for kerosene? The NGK equivalent for the L90 is B5HS or BR5HS, while the equivalent...

I find the recoil starter on my BCS735 with ALN330wb engine retracts the cable very slowly. Would a cleaning, oiling or tightening the spring help this? Any suggestions on how to do this? Also, the cable has eaten through the faierlead (part #108.022). I'm going to rotate the starter...

I find it challenging to change gears on my BCS735, especially getting it in and out of 1st due to the angle of the shift rod. It can be finicky when moving into gear or neutral, and I have to play with it to get it right. Are there ways to adjust this so it is a smoother process?

After extended use of my BCS735, I find that the clutch won't disengage. I don't have this problem when I use it for short periods of time. I've tried various amounts of play in the cable, with the same result. Also, I want to verify that others find the clutch handle to require significant...