Search results

My 2005 NH TC 29DA has the original front tires.They have been plugged and are starting to show cracks. What tire is a good replacement and where to buy with mounting? They are TITAN 25 X 8.50 X 14 NHS MAX LOAD 2000 LB rating on it now.

Geotextile fabric covered by a few inches of fine crusher run

I just successfully installed the NAPA KS 6600 switch in my 2005 NH TC29DA. As suggested, I connected both red wires (B&D) to BAT, one white wire to ST, one orange wire to IGN. Everything works as it should, I don't know how but it does. The tractor starts every time so far. Thanks all for the...

Hi all, My saga continues. I replaced the battery cables and thought that my starter problems were solved but not so. Still randomly clicking so I decided to upgrade the ignition switch to the NAPA KS6600. I was able to find one for $ 50 with my military discount and thought that it would be a...

So far, I have ordered 2 solenoid stud extenders, 1- 5/16 x 24 and 1- 5/16 x 18 and neither one seems to fit. Is this a metric stud? and if so, where would I find a stud extender? Any help will be appreciated

Ignition Switch with Keys, Tractor Ignition Switch 86405634 Replacement for New Holland Boomer 3045 2035 3040 20303050 T & TC Series Tractors T2210 T2220 TC29DA TC31DA TC33DA TC34DA TC40A 22.99 on Amazon if you ever need one.

NSP-1467S, 5 Gallon Gas Can for Diesel Fuel with View Stripe, Pricey on Amazon but works very well with no issues. I have 6 for ethanol cans for my generators and 2 diesel cans for my tractor

I agree that greasing eqiptment is a major PIA. I have a Milwaukee battery powered gun that is just about impossible to purge air from. I also have used the grease fitting lock device with mixed results. I use cream colored synthetic grease that makes me think everything is cleaner even though...

Thanks for the replies, the tractor now starts with more gusto and no click. It obviously was not getting a full 12 volts to the starter. Has enyone ever used a starter solenoid stud extender. I ordered one because I am not happy with the wires crowded on now. it is 5/16 x 24 thread, I believe.

I checked everywhere online and at 3 local NH dealers for the positive battery cable. No local dealers had it in stock, all could order it for $ 206.00. I went to Tractor Supply and bought both positive and ground cables for $46.00. I had to add the 3 additional wires and just barely had enough...

I am in the process of changing out the battery cables. Easy enough to remove the ground cable and find a replacement, the hot cable is more complicated in that it has 2 extra wires built into it on the starter solenoid end. I know I will have difficulty finding the factory cables but does...

My 2005 NH TC29DA has an intermittant starting problem. Some days I turn key, let glow plug light go out and it starts great. Other days same procedure, just click, click. I keep trying and eventually it always starts, so far! I have read previous posts regarding this issue a long time ago...

The QR on my NH bucket became very stiff to operate over time. Upon closer examination I found grease fittings to lubricate the pins. That and a little spray lube, what a difference! I did have my pallet forks come close to falling off once so I can understand the danger!

Kawaski Mule SX 400 would be perfect! Simple, cheap, reliable!

I have 60 acres and find that my 2019 Kawasaki Mule SX 400 CC is a perfect mix of quality, price and utility. Not a powerhouse but certainly very usable for the acreage you mention.

All fixed. NH part # 86530740 did the trick. I used braided picture frame wire and a brake pedal depressor tool used to check lights which ratchets. One end of the spring in the bottom of clutch pedal and the other end in the wire and ratchet it until it lines up with the hole in the bracket and...

Thank you, very good suggestion as the spring does look very tight.

I did see that post, however it is quite a bit different than mine. It is under the floor so I will attempt to try installing under from underneath. I hope to do it without tearing the whole pan etc. Thanks for the reply/

Is there a best "easy" way to replace the clutch pedal return spring on a 2005 NH TC29DA tractor?

I replaced the alternator. Made in China $100.00 version. Tach and hour meter now working fine. Go figure!

Thanks for confirming what I was thinking. I will try to test that if and when the tach works. One other thought. Last year I replaced the start switch ( aftermarket from Amazon) after seeing the usual fried contacts, blown fuses and having the no-start condition. What are the chances that that...

Battery cables and grounds are good. The tach wire from the alternator to the instrument cluster has continuity. The alternator appears to charging the battery ( 13.5 volts) even though the battery always requires a trickle charge to bring it fully up according to my NOCO electronic charger...

Load tester that has a heat element. The battery stayed right in the green. It also indicted about 14 volts while running that indicates to me that the alternator is putting out. The tractor seems to start now every time with a fully charged battery and the tach will work for 10-20 seconds...

It is electrical. In addition, a new development has occurred. I put my trickle charger on the battery to make sure that is fully charged. After doing so, no more click, click and the tach works for maybe 20 seconds and then it stops. I think that I have eliminated the battery as it load tests...

Yesterday my tach and hour meter stopped working. Everything else works. Several days before that I had removed the starter solenoid hot wire to clean it as a possible reason for my click, click, click then start condition. I was careful not to disturb the wires on the generator. Anyone have an...