Search results

PumpGuySC "crank the engine until fuel SQUIRTS OUT" Ok I did that and yes the tubes did "pulse out fuel" Not squirt as offered. Then I warmed up the glow plugs turned to crank it and still nothing fires. I even removed the air filter and tried with starter fluid still nothing. So which way do I...

Ok I will give that a shot in the am. After I get some metric flare nut wrenches. S.A.E. works but not always. Thanks again!

Ok PumpGuySC, Ok I guess getting wet shows nothing I will remove the lines and the injectors and are free of obstruction. then crank to check for flow.

Well, there are no shut-off valves in this system I did crack each injector individually and cranked until showing wet.

After a routine maintenance check I decide to change the fuel filter. after changing the filter I run the bleed procedure on the manual seeing little or no air involved. The engine cranks but does not fire up. Tried starter fluid motor bumps but nothing fires. Perplexed I start cracking the...

If I loosen each injector nozzle and crank it should leak right how much deeper do you have to check the injector's output.

I checked on the OP manual and looked at 5-25 and 5-26 followed the instructions no change

Yes it did go away might be a voltage low indication, Still nothing on the start up the fuel system needs to track this down Illustrations ?

Hey I am glad you responded. The new battery cable works it cranks well but I bled the screw and it will not fire up. Now that fuel line is clear from the junction where it splits off ok tried starter fluid still nothing. ??? Um I did this standing beside the tractor not in the seat if the seat...

Hi Tom, Long time no see, I replaced the positive battery cable it was defective on the battery end. Now I am getting a Code on the LED panel showing a "J-1" indication on the screen. What does that mean? As usual, any help is appreciated. Scott

Maybe maybe not I will try that tomorrow, Monday. My arms were not long enough thanks!

Hello Tom, Yes I am still fighting with this on the engine this time. I changed the fuel filter, it was nasty, I let the filter fill and checked the bleed for fuel pretty much air-free. Tried to start and nothing used diesel starter fluid would fire momentarily. I guess I need to look at the...

Tom, Thanks again I have a besko loader valve 801z1-8000 too. I checked the connectors blue and red a bit cruddy but clean up and reconnects ok. The boot and linkage are again cruddy but working ok. Still nothing no dump yet. I will research the valve before tearing it down. Research is sketchy...

Thanks, checking the hoses and boot.

Hi Tom, Well, today I charged up the battery and went thru the lock-out switch and starter circuit everything checks out still nothing I flip up the seat and start looking around in aggravation I pull off the wires with the seat switch one spade terminal looks crusty I grab a wire brush remove...

" I'm sure you are very frustrated with the old girl." I think I wore it out. Granted it has been worked pretty hard. But the electrical is baffling me to no end. I have changed nearly every switch ie. lockout. Tested almost everything and now the right schematic does help. I have changed the...

Yes it's absolutely dead Thanks again

Hi Tom, Here is the latest. after looking around I looked at the fuse box and finally figured out that the wiring schematic is not the same as my tractor mine only has 3 fuses in the cluster not like the schematic here shows four fuses is there another schematic available. Thank you for your...

Hi Tom, So here we go I replaced the OEM start relay with an aftermarket relay and just ordered a new OEM relay. The aftermarket only worked a few times after. The next day then goes to start twisting it to the right then pops and nothing. It might be that the aftermarket relay was not strong to...

Well, it died again, this time I insert the key turned to the left light up the glow plugs then rotate the key to the right to start and hear a click or pop and the main instruments does not show a blank or dead wonderful start to the day. I pull the cover check the fuses and the 40 amp at the...

Thanks for the thought I will try the couplers and maybe bleed the tilt actuators too. I am a bit better at hydraulics although I would like to see an illustrated parts breakdown on the pump. hint hint. One more thought how do they check the pressures or locations ie. ports plugs ? I can plumb...

Goooooood News I have it running and moving it had been sitting for a while. Now the issue the bucket goes up and down ok but the tilt is stuck it will not pivot the bucket. Oh, the last fix was replacing the starter solenoid.

The starter relay is ok running out of things to check, the battery is ok, neutral SW. ok, parking brake ok, rear PTO SW. the big one on right is new. ignition is new. The starter 40 amp fuse is good. A 10 amp fuse in the fuse box is good. The glow plug position lights up. instrument panel...

Tom, HST Neutral Switch - Located on the right side of the tractor, yep found it functions as advertised via mechanical movement. after looking at more things involved I am going to check the starter relay next. trying to trace this out on the 4 pin relay next.

Hi all, Finally trying to get this done Thanks to you I found the brake switch, but I cannot find the neutral switch yet again a picture or a drawing would be great.

Thanks I have it now again many thanks

Hi again, I have replaced the PTO switch and no joy and it is a XJ2025H I thinking there must be another one. Yet again a wiring diagram would be helpful.

Hi, All I have a XJ2025 with issues I know that if you unseat with engine on it will cutoff also are there any other switches that will do this. I would love to see a good wiring schematic on this tractor.

Old lurker now with a xj2025 with hydraulic problems about after an hour here in 90+ florida rpm and hydraulic dies frequently I assume its a hydraulic problem unless the pto or front loader is under a load. This is 2 years old with 200+ hours. All filters hyd and hst have been changed and oil...