Search results

Supposedly according to PUG, all/most parts can be obtained at a NAPA or good Hardware Store...There are employees at a store like NAPA (old timers) who could find the right strut and spring. Also check johnwaynes facebook link.

Good idea and modification.

Hi Kevin, just saw your post from last month...The person I bought mine from has had to do that on mine. In a nutshell, you have to remove the bed, then the axle nuts and pins have to be removed. The nut you have to access, in between the frame and tire, provides almost zero access for a...

John, did you see my other post regarding the starter...I have to remove mine and haven't seen any bolts to remove with exception to the two that go through the end plate. Those, I think, are for accessing the armature and brushes.

Hi John...had to look at mine because didn't remember seeing shocks on the front but there is and they are the strut type. There inside the coil spring and couldn't see any markings on them. Now my backs had labels that said: Car Quest Gas Charged XD Tried to send you an e-mail...

Been trying your e-mail address but so far 2 failures...I must me copying it incorrectly. If you get this, send me another one w/ it. Thanks

I'll do that w/ a piece of fuel line. I saw some motor assemblies on either E-bay or Amazon that aren't expensive...just have to determine which one would fit the PUG application. Thank you for your thoughts and help.

johnwayne, I removed the top of the carb. and there was alot of crud (looked like disintegrated red gasket seal) in the front side at the bottom. Vacuumed bowl out and cleaned w/ carb. cleaner as well as the needele valve on top and passages. Put it back together and difference between night...

JW, you've been busy and so have I but to a lesser degree based on my skill set. Hope the pictures helped in designing your tale-gate and associated parts; if you need more let me know. Having trouble w/ mine running...checked out vacuum/pulse fuel pump and based on the tests it is fine...

Having trouble w/ engine idling...where on the carb. is the idle screw located and how do I set it? Also acceleration isn't smooth which may be associated w/ proper idle adjustment. Have replaced all fuel line, filter, cleaned out tank and carb. looks clean...suggestions? Thanks

Try 1-(606)-872-0549...ask for Michael.

Here are some more:

johnwayne, sure, see if these help and if you need more let me know.

I can send a photo but not clear on what you specifically need. To me, a tailgate is the dump bodies rear access point. My parts manual has diagrams of different sections of the PUG. Will any of those help?

Home of the Free because of the Brave

Are you in MS....I have one also made in JXN. Have to replace brakes on mine and saw the link for parts on page 4 of this link.

Looking for some parts for this Model PUG...heard there was someone in KY. who bought out PUG/or has parts for them. Thanks!

Having trouble getting my starter set up working I've replaced rewind spring and rope. This model has the wrap around spring, then cassette holder for same, followed by a plastic housing that catches rewind spring and houses starter rope, then another spring that sits in this housing, followed...

Not paper, but ones that hold rounds. Question, do you have to go through a FFL to buy a rifle magazine now?

saw has been down for couple of decades and now working on it. Tried to get to the point to see if ign. coil is still working. Had to remove rope assembly to clean contacts where ign coil makes contact w/ magnets on flywheel. Long story short, couldn't determine how the plastic cog between...

On a MF-135, how do you keep the box blade at the same level/height? When box balding my road, it rises and lowers creating gouges and high spots. If I turn, the blade will rise and then lower after I straighten out the tractor. Yesterday I tried to clean up small debris in the woods and...

Trying to locate year of my MF 135 diesel tractor...nothing under steering wheel panel or behind air cleaner on right side below battery box. Any other ways or places to check? Thanks

Hello to all and I'm new to the forum and living in the state of MS. Presently I have a MF 135 diesel and my first tractor was a MF 65 propane. (27 years ago) Look forward to learning new information and meeting members.