Search results

I should add I didn't weld on the ROPS, I bolted it to the tab that had the SMV sign bracket attached.

Decided to mount a .50 cal Ammo can to my ROPS to hold tools, chain, clips, etc. Used some scrap 1/8 angle iron I had laying around and stick welded this up. Can is a light friction fit so I can remove if needed. Time will tell if I need a standoff down to the fender for support.

2018 CK4010HST. 130hrs on it, oil has not been changed but the filter change was done at 50hrs at the dealer when I bought it used. Oil level is correct in the trans.

I was working the tractor yesterday and needed the diff lock. LOTS of force on the pedal got it to lock, but to unlock it I had to stick my shovel handle under the pedal and pry it up, even after 100 yards of driving swervy to let it pop out. Is something bent inside the trans? I have been...

Thanks! Any idea of the chunky black stuff? Is there any harm or a way to add a pre filter from the tank? I store my fuel in justrite steel cans with some diesel kleen additive. I buy 5 gallons at a time, I only have about 8 acres to brush hog.

It was 115 heat index here today. I waited until 6pm to go out and run the tractor. A few tours in Iraq and I hate the heat. I hate being cold worse though. 20 mins oer hour of easy activity outside is about all I can take in this heat.

I use the Lucas red n tacky and I store my cheap rural king Grease gun on some shop towels in the cabinet. It drips a tiny bit. Like two drips per tube ish

I have a 2018 CK4010H Kioti and it was giving me a run of water in fuel lights with subsequent drops to limp mode. I did store it in am unconditioned barn since I bought it (early 2020 with 55 hrs on it.) It now has 126 hours. I did not have the tank topped off that I can remember over the...

Not the whole shaft, just the end yoke with the spline connection. I installed a new bareco pto shield and realized the slip ring collar was messed up. Just need that end piece and want one that uses a push pin type instead of the collar.

I bought a used rhino 260 rotary cutter and it needs the end that Hooks to the tractor pto output replaced as the collar that pulls back to release is bent and hard to manipulate. I want to install the kind that has a push pin instead. The Rhino part number is 00779516 but I can't find anything...

Maybe some big washers on each side?

The kit that does the whole shebang is 00779533 part number.

I just bought a used rhino 260 rotary cutter and the pto shaft safety cover needs help. Really just need the two plastic "bearings" and the two end cones that cover the slip clutch and pto coupler. Is there a good source for this that I don't have to buy the whole rhino kit for 210 bucks? Also...

I have a ck4010hst that the bar between the diff lock pedal and the actuator on the diff housing bent into a pretzel. I didn't stomp on it. Even driving in circles or having one tire slipping in the mud and applying pressure to the pedal would not engage it. Tractor is a 2018 with just over 100...

Yep but it was rougher than I expected or wanted to mess with. There are quite a few Alamo 88" mowers I found but they are all 5 hours away

Went and looked at the one with tail wheels today. Rear roller is missing and there was a lot of glob welds patching things back up. The side slicer knives were very badly worn to where the little angled part was almost worn away entirely. And the input seal on the gearbox was leaking. The blade...

I am going to look at that alamo one with the rear wheels on Friday. Does it really need the rear roller if in fact its missing? Also, what are some must-check items before I make an offer on it or go through with the purchase? Just want to make sure there arent any show stoppers.

I cannot bring the tractor to the mower

How much does it weigh? I have a kioti ck4010hst asking price under a grand

What flail would this be? It's a 6 foot cut and has trailing wheels behind?

Lost out on the cheap mower to someone else. The search continues

Here is the seller's picture.

I'll go have a peek this weekend. I am actually wanting to get a rhino tw25 to cut the nasty heavy brush I have at the new place. But a cheap flail would be fun

I found a ford 907 flail 6' wide for 150 bucks. Seller says it needs a bearing and the belt is a little worn. Looks to be complete except for one of the knife assemblies. Its rusty so would need a good cleaning and paint job or minor restoration. Worth picking up? Its been for sale for a long...

I want to say it's the original engine but there are no decals or stickers or anything on it

Yeah, its a little over 600 bucks. That's why I want to have it repaired if it needs it. I plan on getting it running a bit better and testing it before I do to much else to it. Blower fan? You mean the whole assembly?

its a 1989 model!

I figured out the suction issue, I am an idiot. When using the hose on the side, you have a flapper door on the bottom that needs closed. Sucks like a champ! The impeller has a little wear on it on the middle of the vanes. I believe it is cast aluminum. Think a machine shop could weld it back up...

Anyone ever mess with one of these? Picked it up today. Cleaned the carb and it runs pretty well, but doesn't seem to have a ton of suction even from the side hose when I connect that. Any ideas? Sources for a manual and parts would be awesome too. What is the value of this thing? It's not...

I checked my pto shaft carefully yesterday. I got my 1/2" impact out and tightened the stump jumper nut as much as I could. Still a little shake. Pulled the shear pin bolt and it was actually a little bent, so I threw a new shear bolt in it. Damn thing mows like it used to again, who knew...

Any suggestions on a cutter that can handle a little abuse would be appreciated. I have 35 PTO HP

Yes it has the stump jumper. I am going to pick up a 20 ton jack today to get it pulled with my chains.

Just checked the top of the deck, definitely not bent

So i was cutting some light brush the other day and my cutter started vibrating something fierce after hitting a 2" small sapling stub i didnt see. Shut it down and took it to the shop. It is a king kutter 72" flex hitch deal, tractor is a kioti ck4010hst Blades were not stuck together nor do...

Good Evening all, I have been lurking on these forums for several years and have learned a LOT of good information over that time, so thank you! I just recently sold my 1950 ford 8n and bought a new (to me) 2018 kioti ck4010hst with 52 hours on it. Got a new 6 ft rotary cutter, pats quick...