Search results

Just an update. I still have the tractor. Around 900 hours now. I had to replace bearings in both front wheels. Caused by snap ring breaking and wheel and axle stub coming out. TYM upgraded the snap ring to a better design. The steering shaft stop leaking on its on. I never did replace the...

Anyone ever had their TYM tractor go into derate mode? :confused:If is there a way to reset the cpu? Removing power for 24 hours did not work. I am unable to find anyone with a yanmar smart assist unit. Thanks

Anyone know where the OBD II port is?

Anyone know where the OBD II port is.

Today the LF wheel bearing went out and wheel came off. :( Cabela's (TYM 454 and 554) Now to find the part. Oh what fun.

Ran it to a little problem the other day while moving dirt. Loader would not go into float and raising the bucket with a full load was a little slower. The problem was in the end cap on the loader control valve. Inside the cap is a ring nut that holds the three balls for the float pos. The nut...

To the owners of Cabela's tractors that still have warranty. Looks like we are left out on our own to get repairs. I have two problems that need repairing. I thought I had two more years of warranty. When I bought the tractor a year ago they said they would continue to repair them even though...

I don't care if you call a fart a poot. Sounds like a clutch problem to me.

LOL

Anyone know the fuel filter part #? I think it has a bosch electric pump. Filter is in the pump.

This hole all the way through. Remove piston gear first. On my big saws the pump runs at idle.

Had a husky 450 for a few years. Was bad on bars and sprockets because of the non adjustable oil pump. The pump on this model does not pump at idle when the chain is not moving like on bigger saws. It was only using 1/2 of oil per tank of fuel. I took the pump out and drilled the hole...

Anyone know the location of the pressure relief valves? Loader needs a little more pressure. Probably set a little low from factory.I assume there is one on the loader spool? Can not find anything in the owners manual.

Anyone have this on your tractor? Used for plowing maybe? Owners manual does not cover this other than say there are 3 modes and a on and off switch.

Talked to the mechanic when I picked up the tractor. He's old school like me. "Turn up the pump and roll coal". :) He said it would not trough any codes if I took the filter out of the DPF canister. He also has the scan tool and can reset the computer at any time. Nice guy, I hope he works for...

Anyone have the front axle housing go out? Mine(left side) went out at 750+ hours. Easy repair but had to do it where it broke down in the field. I was spreading rye/oats/clover with a three point spreader when it happened. Had to go get another tractor and dump the seed out of the spreader and...

While using loader tractor shut down. No power to switch or anything. Didn't have a meter with me to check. Manual says three 50 amp fuses in wiring harness. I know one is near the battery. Anyone know where the other two are? Plan on going back to the farm with a meter Saturday to see if I...

I want to turn up the pump on my 675's for more power. Thinking of two turn but I don't know if it is CW or CCW? Anyone know.Has perkins engine rated at 72HP. Should be able to get it over 80hp with no problems.

Anyone know a way to increase the output on a 450 oil pump? Love this little saw but its bad on bars and sprockets because of the lack of oil flow. Goes through about two tanks of fuel per tank of oil. Didn't know if there was a way to mod it or an aftermarket replacement pump with more output?

Name one place I can get parts. Made by TYM but the parts I need( front grill and headlights) are not the same as the TYM 273. I replaced these same parts a few years ago but because I keep running into my dump trailer I have messed them up again. Now the dealer I got the replacements from a few...

Noticed that my loader was a little off center and had some loose side to side motion to it. Found both sides cracked where the loader frame mounts to the flat part that bolts to the main tractor frame. Will have to weld it up before I use the loader or it will break from the tractor. Anyone...

Looking for a cross for the 26560201 perkins fuel filter.

Picture of sub frame connector.

So my montana 2734 frame broke into while using the loader. A little over 600 hours and I use the loader alot. I knew this was a weak link all along. I had been planing no building subframe connectors to connect the loader frame to the axle but keep putting it off. I took the loader off, removed...

Anyone having seal leaking on theirs? I now have 530 hours on my 7 year old Montana(tym) T2734. Front axle seals have been leaking about a year. The ones on the ends of the axle started first then the one where the drive shaft goes in. I ended up switching to 00 corn head grease, then later to...

Anyone having seal leaking on theirs? I now have 530 hours on my 7 year old Montana(tym) T2734. Front axle seals have been leaking about a year. The ones on the ends of the axle started first then the one where the drive shaft goes in. I ended up switching to 00 corn head grease, then later to...

Need part # and online parts store link. Thanks, BS

Need Part # and online parts store Thanks, BS

No chainsaws but I am going to pick up a powerhorse 3 point log splitter from Northern Tool. Instead of using my tractors rear hydraulics I want to use a pto driven pump. I plan on using a PTO pump by Prince with 21gpm flow. I will also use a 21 gallon tank and a filter. I know the return (out...

OK so I am going to pick up a powerhorse 3 point log splitter from Northern Tool. Instead of using my tractors rear hydraulics I want to use a pto driven pump. I plan on using a PTO pump by Prince with 21gpm flow. I will also use a 21 gallon tank and a filter. I know the return (out from...

I have one I am going to sale. Bought it in 2009 Has low hours, original 16" bar and chain have sharpened chain a few times. I have 5 other saws and this is my smallest one. I am in the firewood business and this saw is just too small for anything I do. How much should I ask for it on ebay, or...

Any dealers on here know if Montana is still selling the Montana Limited? I bought a 675 DTC a few months ago and like it so much I would like to buy a 665 or 675 in two wheel drive. I checked the local dealer and they have sold the last ones they had in stock.

:( So sorry

:( Had a 6.5 HP Intek Pro irrigation pump running Saturday. Ran about 20 minuets and stopped. Checked everything out and looked like it had jumped timing. Took it home and tore in to it. Plastic cam broken in half. Who would have thought:mad:

Need to move a 6000 lbs tractor. I have a 16' trailer with two 3500 lbs axles(should carry 7000lbs?) I have a 2005 Z71 Suburban to pull it with. I do not have weighted plates on the truck. Legal in NC or not? I can get a 4.5 ton trailer if needed, but would like to use the one I have if...

Need Filter( hydro., fuel, oil) part #'s for Montana/Farmtrac 675 DTC. Does not have to be Wixx. Thanks, BS

Looking for a little advice on some land I had logged. I had 30 acres clear cut and am planning to replant most of it but would like to leave 2 acres for a food plot. What would be the best, or most cost effective way to remove the Debris from the 2 acres? What is left are a lot of limbs...

Never put too much grease in the center pivot joint on the front axle of a T 2337 :(

I carried my Montana tractor in to the local Dealer here in NC to have a few things repaired that should have been covered under warranty. I have only had the Tractor seven months. I told the guy that works there that if the problems were not covered under warranty do not do the repair, as I...

Looking at a T2734 with loader to use with a 3 point sprayer, box blade, post hole, rake, ect. They have three in stock, 2006 inventory. When I first ask about them last month the price was $15,126.00. The guy called me back and said he would take $14,500.00 for one. Is that a fair price? Seems...