Search results

I I used a mechanics stethoscope on the pump and I hear kind of a wheezing /whirring noise. I’m going to do what you just talked about now .

The power steering pump hard steel lines with rubber lines closer to the front of the machine . The 3p / loader pump there’s a 3/4” hose from the top of the pump to the loader valve. The suction lines from tank to pump are all steel, with o rings bolted to their respective hook ups( not the...

Sorry for the late reply . As for the update . Only getting low pressures on the gauges. The 3 point hitch goes down , but won’t lift with 2-300 lbs on it. I have noticed some leaks which I’m working to mitigate . I don’t think it’s the pump but I can’t say for certain . My next guess would be...

For whatever reason my draft link at the bottom can be seen dripping slow drips of hydraulic oil. Also I have this icon on my dash (unsure why ) . From the back , the switches allow me to lower and raise the 3 point hitch . Still no loader valve . Taking the timing to de-grease everything. It is...

So my 3 point hitch is working under load . Could this be something stuck with the flow priority valve ? I need to read more about the oil passages .

its a m100x. Its a cable controlled open center hydraulic system for a loader controls are mounted in the cab. the 3 point hitch is working. The valve is leaking a very small amount, i just havent degreased it to find where.

Could it be possible that I have the centre valve that puts fluid into the ports located incorrectly ? . My pressure gauge is off the “p” port .

The pressure gauge is showing 30-40 psi when the control valve is open . (Lift bucket) The open centre valve has a direct connection to 1 of 2 of the hydraulic pumps . Appreciate the responses . Hopefully I can narrow this down tonight .

I always find warming the motor up before a plug change helps. You can use a penetrant, make sure around the area is clean before you pull the plug . The biggest thing is do NOT over tighten then . Also check your gap. I personally wouldn’t use champion , but that’s a personal preference.

it first started having issues with the FEL, slowly creeping down . Took it into the dealer because I was just flat out busy , (huge mistake). Seemed fine at first then eventually it stopped working all together . I pulled the valve apart to find some parts missing (heater plug) . So I got a re...

yes it is a T. I tied into the P port.

good afternoon i have a kubota m100 that i am trying to fix. i have the valve rigged up with a pressure gauge but havent been able to get the pressure i want out of it. in fact theres not much for pressure at all, but upon cracking the hose from the pump there is hydraulic oil in the line...

I emailed you .

Does anyone have the 314 page service manual on pdf ? Thanks .

It was for John Deere but thanks .

Hello everyone , I have a Deere stx38 and a L110. One has a spicer 4360-100 the other has a 4360-068. Just wondering if anyone’s used these transmission parts interchangeably. I haven’t had much luck with google. Thank you .

Loader doesn’t work. It’s dripping . Not a significant amount. The steering is working /3 point is working . There’s an oily residue under neatth the machine , but no dripping . It’s taking sufficient oil over a short period of time .. the engine oil level is fine .

So my loader bucket valve is still dripping . I have found some oil residue over the bottom of the transmission and pump. And some of the hoses . I’ve added 5-6L over a handful of starts no I’m not exactly sure what to do next . I could try degreasing the machine , I feel like it could be an...

Thank you for your help.. will keep you updated

Thanks for your tips . Just an update. I’m currently cleaning parts and finding debris here and there . Hopefully once i get it back together and install it functions , we shall see .

My apologies. Do you mean this diagram ? I haven’t been able to find an diagram schematic for the valve in the repair manual other than this one here I previously posted

This is what I was able to find in the manual

PB feeds into the hydraulic regulator

I’m concerned because I’ve had the valve apart and rebuilt the centre open centre valve , and it’s not giving me any hydraulic power . I wonder if the fluid is even circulating through . The valve leaks a bit .

My loader is being a pain in the arse and I just want to disconnect it and pull the valve . My3 point hitch is still in good order . Am I am to cap the P, PB and T line from the pump to valve and run the tractor without these lines ?? thx .

How do I clean it out ?? I’ve put some air to it . Varsol tank ?

I’d like to cut the valve out completely, until I can determine the issue with it . My 3 point hitch is still in working order .. just changed my filters for good measure .

It has 2 actuator spools , and the centre regulator valve. It’s an open system. It had some leaking issues so I tore it down and put a new seal kit in it. The brand is Alo /quicke. Case/IH and Kubota have used these loaders over the years. Maybe I missed something. I will go through it again ...

Yeah. Mine is joystick . It’s mechanical . Still no pressure

There’s pressure to the valve . The pump is pumping fine . Just not to sure why none of my spools are allowing fluid to my bucket … maybe it’s something simple , but I’m stumped

Still no results. Will be the day testing again

If you want to buy some time , try Lucas oil stabilizer . I don’t think you have a fuel issue. As it was stated already, check your rings and top engine. Remember additives do not fix broken or worn parts but they can buy time sometimes with the wearing process .

That’s something that Is overlooked . I will double check it , thanks

Hello. I’ve got a Kubota m100 with a quicke loader. I’ve re sealing the valve, and have tested the pump. It has pretty . When I hook the valve up to the 3 hoses and operate the spools , I have absolutely no pressure to my hydraulics. If rebuild the centre valve but I’m wondering if I don’t...