Search results

Plastic

I am definitely going to pursue a replacement, great suggestion.

Appreciate the responses. I did some YouTubing and figured out how to check the fuel gage. Removed the instrument cluster and applied current (using a 9v battery) to the positive and negative lead on the back side of the instrument cluster. Then took a test wire from the tank sending lead to the...

Good evening everyone, could really use some help diagnosing my 3510 fuel gage. With 3/4 of a tank the gage will only raise to 1/4 at best. For those that have had a similar issue where might I start?

My 2005 3510 is a TYM build.

A easy way to tell the difference between the early and late is the sheet metal and grill. The “late” had a swooping rounded nose grill while the early were very boxy. Early also had a yellowish/tan rim while the late had silver. I have a 2005 late model with 1300hrs. It’s been an awesome...

Here are my remotes and the excerpt from the manual. It suggests holding the lever in push or pull position will cause the oil to travel through the relief valve and cause it to overheat. There is no detent on the lever or proportional valve that I can find. If I use a bungee cord will this...

Found a log splitter locally on CL and would appreciate a sanity check on whether my tractor can handle it or not. The splitter is a Speeco 400197 that runs off the tractors remotes, I would like to use it on my Mahindra 3510 gear tractor. From what I can find my tractor is rated at 6.4 GPM...

I’m having some charging issues with my old cub cadet model 86 with a 10hp Kohler. It wasn’t charging, with a meter hooked to the battery at full throttle it was outputting 12.5 v. I bought and replaced the voltage regulator, it is now charging at 16v! Is there an adjustment procedure I need...

Hello all, Looking for some help with my 2006 Deere 997 zero turn, I bought it used a few years ago and have accumulated about 2200 hrs on it. While its down for the winter I'd like to do some PM work, specifically adjust the valves. If anyone has some guidance on how to set TDC and how to...

Here it is. Quality is very good, dry run with no snow worked great.

I have a Pats quick change system and it’s working nicely with most of my implements. I decided today to check my snowblower and realized the PTO shaft is too short. Do any of you guys use PTO adapters for making up the missing 5”? If so which one do you recommend? My blower gearbox shaft...

For all of those currently using a Pats Easy Change Quick Hitch I have a few questions... -How do they respond to tightening the stabilizer arms on the 3pt? I致e always snuggled up on my adjustable drag links to minimize any float on my scraper blade or finish mower. I知 slightly worried with...

I've done a search and can't find any current information, does anyone know where I might source a grill guard for my new style (2005) 3510 that will work with the ML112 loader?

Rustoleum sunrise red: Krylon international harvester red:

Im guessing an adjustment is due, I noticed today after about 2 hours of loader work when you shift the shuttle lever into neutral there is a faint grinding noise coming from the transmission when the clutch pedal is released. I never really noticed the grinding noise until it got good and...

I have been going over my 3510 and have a question about the clutch pedal adjustment. The manual says there should be .78 - 1.18" of freeplay, my question is what point of reference is the freeplay measured from? Is it full pedal extension (at rest) to the point of engagement?

Think I found my problem

Is yours the new style or old style 3510? I can’t seem to find the access panel.

New owner of a 2005 3510 gear tractor, comes from a 1 owner garage kept house with 1200hrs. I have a few questions, hopefully you guys can help with. I noticed on the back of the tractor there are two remotes, the original owner stated he never used them. I don't see a valve or lever...

I don't have a manual for my tractor and would like to change the Hydro filter, where do I add the oil once I pull off and replace the filter? I am guessing under the hood in the power steering resivoir? What type of oil should it use, standard hyro oil?

I found a 506 brush hog mower locally. It was shed kept with no rust and the gear box/pto shaft works great, only issues are the back skirts are dented up pretty good, there was a weld repair to the back wheel shaft and a small crack that needs fixed on the frame beneath the RH side 3 point...

I have a MF 1035 tractor with the 1016 loader. I know the 1016 loader is supposed to be a quick detach loader, since I do not have any manuals for it is there someone out there that can give some insight as to how this loader detaches? Or a copy of the 1016 loader manual? Any help is much...

I'm new here and could really use some help. I have a MF 1035 with a 1016 FEL with 1250hrs on it, the other day I was attempting to pull a pipe out of the ground and heard a loud pop come from the front LH side. I went to back up and the front left tire was locked up. I brought it in the shop...