Search results

I have a yellow Typhon Terror XVIII and was looking for the same. Did you find a color match semi-close? The New Holland Yellow or Transport Yellow look like one might be close. If you haven't tried one or both, I may try at least one of them to see.

I have a 6' Box Blade from Titan Implements in Decatur, TN. I used it for my 30HP Yanmar and works great. I plan to use it on the L4701 and expect it to work a little better with the size.

I bought my pallet forks from dealer in KY. Tomahawk attachments Nappanee, IN both grapple and forks. I am pleased with both so far.

I am very happy with the tractor. It is basically new and the features and capabilities are expected and exceed what I previously with a smaller tractor. I love having a quick attach loader for pallet forks, bucket and grapple. I need and want a Lane Shark. I have several roads to maintain...

I am using the grapple for all sorts of chores. It's saving my back and in time. Agreed that the ordeal helps you learn the tractor.

Good news. Amazing the same thing too. Easy fix but sometimes you have to find everything else too. Same symptoms I had. I was sure that is what you too but when checked first time I was not sure what else..... Now its time to install your 3rd Function going....

Tractor is 35 miles away. I don't have completed pitures from the project. I took before-pictures to see what I was planning and tried to make sure what I would need.

If you can find the right connector and add on the end of the leads you plug into that. If not, I just added and crimped a quick connect female and male and plugged them into the existing terminals.

i believe it is: Kubota: SUPER UDT2 Universal Trans-Hyraulic Fluid https://www.messicks.com/part/70000-40205/5gal-super-udt2

Sorry, I was hoping that was the same easy fix that I had. I would make sure the right amount of fluid first. I dont think it will matter which the up/down curl of the loader. Its sound like the loader is functioning properly. It's more about the flow of the fluid properly through the system.

I connected to the spare wire under the right side fender that is used for a work light. I will eventually put work lights so I will have to find another spot, probably under the dash. I didn't use straight to the battery because I didn't want it always "hot"

There was very little dripped from the hrydraulic fluid when I switched. Just enough wipe a small rag. It was easier than I thought.

Then after got that fixed it I got the Summit 3rd Function Valve and added a Grapple.

I just added a LA765 loader from a dealer a week or so. I had the same thing. The lines from the block to the valve to the joystick controller were swapped. The loader functioned fine but the 3-pt would only work with the loader controller and the 3-pt lever together. I called the dealer, they...

As was suspected, one of the lines from the block to the valve was reversed. The dealer sent a diagram from the installation manual. Swapped the lines as works as it should.

I believe it is an OEM rear remote.

The L4701 did come with a single rear remote. The dealer rep called me a little after 6PM and their service guys were gone for the evening. I live 35 miles away from my tractor. They are going to get me on the phone tomorrow when I am with the tractor and troubleshoot. To me it appears one of...

That is what I was thinking. I have a call into the dealer. I wanted a sanity check too. Thanks

So I purchased on a lightly used 2020 L4701 consigned Deere dealer last week. Now, I just bought a LA765 loader from a Kubota dealer that also installed it. I Brought it home late Friday and tried to use the 3pt on a grader blade and does not go up or down unless I use the curl control on the...

Here is a side shot:

I would add my remotes myself if I could figure out what goes where....

Yes. I have been looking for what specifically was on my 2610. It has a small lever you. If I need to raise more on my three point. I can pull this and make the implements higher. I need this for heavier implements like my Bush Hog.

So, I have a YM2610D with a loader (I guess Yanmar too) that I acquired in 2002. In the last 18 years I have never had to put the tractor on a trailer and take to a mechanic to fix anything. I have close to 1200 hours on the tach. It probably had ~450 hours when I bought it from the...