Search results

Ok I will get it somewhere that I can blow it out and hose it out. My property doesn’t have water or electric yet.

Hi there, quick question regarding my Mahindra.. it has a ml108H loader on it. Seems smooth going up and dumping but extremely sensitive and quick jerking when lowering.. Using some clamp on forks the past two days to move some 10ft logs around my property and raising it is smooth… but tilt...

Do Mahindras use a 50:50 ratio?

That’s the issue. I recently purchased it about a month ago and have only I used it a few times for extended times to where it just creeps up. The times I run it for short spurts it’s right around the 1/4 or under half area so I figured that’s its normal running temp. I do want to blow/hose...

Hi guys, I had a “check” light that was on with a fuel solenoid issue and the stop light brake switch not working. I still get the light on when my tractor is used for some time and my engine gets hot. My question is.. is there a safety switch that causes that “check” light to go on if the...

I assume the brake switch is either the brake safety switch or the brake light switch?

Ok update on the issues. I have looked at the radiator.. seems to be clean and filled. I haven’t run it much since the light turned on so I will keep an eye on the temperature as I continue to use it. As for the sudden shut off and check light… Sudden shut off I believe is either this...

Reading that thread… I want to look at the seat safety switch, the brake safety switch and go from there

As for the dashboard plastic cover… When the light first came on, I couldn’t even read what the lights said. It was so oxidize. The way I got it to look the way it does currently. I took the five screws that hold the upper portion of the dashboard out, and I unscrewed the instrument cluster...

I don’t believe it is boiling coolant. The jug is up to the line. Unfortunately I’m not sure on this 100% though. It definitely seems like it’s running hot after being used for a while. But it was also 90° high humidity real feel temperature of 100° that day. I have scoured the Internet as...

Any help is appreciated Maybe somebody else had the same experience?

Here is the picture of the light. The other two is because it had just shut off when I took the picture.

OK, update for you guys. Radiator seems to be clear and is full of fluid. Every time I went to use it after a bit, a light came on under the speedo/ RPM gauge. My gauge plastic was way too oxidized to see what the light said. So I took it apart and cleaned it and then use some silicone...

I will check that tomorrow when I get up to the property

Sorry here is the temp gauge photo

Hi guys, a few issues I noticed while using my recently purchased 3510 for the first time doing a decent amount of loader work today… 1. I noticed the temp gauge was higher than I thought it should be. Granted temps were 90°.. higher humidity.. real feel 100°.. attached is the photo of the...

Hi there, I was wondering if anyone could send me the length and a picture of their Mahindra 3510 loader level rod as well as where the rod is mounted. The tractor I bought..old owner must’ve broken it off for something… all I have is the red support sleeve and I’d love to have a rod to know...

When you took yours apart. Was the detent groove at the bottom of the cap or towards the spring?

Ok, a little delayed because tonight was the first time I was able to get up to the property and work on it since I was last there… I took the cap sleeve and ball bearings out. Mounted it back up and the valve seemed to depress fully as if it would go into float mode. I brought home a little...

Spool valve** ^^

That’s a good question. I did not try mounting the screw valve onto the bracket and just trying it without the cap on. Steel wool might be a good idea. The ball bearings themselves are a little rough, not smooth and the walls of the sleeve do have a a little rough spots on them. When I get up...

An update on the valve issue. I took both caps off.. brake cleaned the crap out of both removing all the crud off. I wd40ed the piss out of both and used red grease on the sleeves.. I was able to get the fast dump to work but still having a hard time with the float. The lever doesn’t want to go...

😆 duh 🙄 that’s my blonde moment for the day. Next time I am up on the property I will take a look at the valve and try and clean everything up

Ok I did notice a groove in the bucket tilt as well. But that groove is up by the spring… where I put the groove on the up/down at the end of the cap after. That’s where I second guessed my reinstallation. I don’t notice a fast dump click on my Valve. I didn’t know it had that. The valve...

When I cleaned it up and reinstalled the sleeve over the all bearing and needle I put the groove on the bottom side of the cap. Does that seem right?

Here is what I found when I pulled the cap off the valve. Both were pretty caked with gunk. Unfortunately I was in the woods on my property that I’m building my house and didn’t have cleaner or penetrating oil so I used diesel 😂 I cleaned it and put it back together. Unfortunately Im not...

The tractor has sat outside for years uncovered so I could see it being rusted. Inside. Poor design flaw. I will pull the caps off and see if anything is rusted stuck

Here’s some questions. Maybe a dumb ones but if I unplug the loader quick connects and take that cap off the bottom of the valve to see if it’s stuck or something. Will hydraulic fluid be pouring out or not much since the pump isn’t pressurizing the system? I assume if I take it apart.. I will...

Yeah, it’s on Mahindra 3510. I attached a photo of the little diagram attached to the control valve. It shows to push it forward almost in a detent manner, but it won’t allow me to push it past the loader drop

Here is my loader control valve. The loader is a ML108H and the little diagram shows a float function on it.. and to push upwards past the loader down. If it’s like the other tractor I use.. I’d assume it “clicks” into the float position 🤷🏻‍♂️

I wonder.. would the control valves are the same?

Does anybody have a manual for the Mahindra ML108H front loader? I was curious to see if there was an exploded view of the control valve for the loader

Well, I believe it’s a 2004 so if it’s been sitting outside for most of his life, I would assume that could be an option. I will have to take a look into that a little bit.

Right. I know it’s different brands but the John Deere I use at work does the same thing. You push it forward and it’ll somewhat click in and stay there. I have pushed forward with some decent pressure and it doesn’t want to move any further past the bucket drop position.

I have a Mahindra 3510 with a ML108H front end loader on it. The little picture on the loader control valve shows that it has a float function if you push the lever forward all the way.. mine won’t allow me to push it all the way. It’ll only go as far as dropping the loader. There’s no extension...

Pm sent! Good to know. I have the Mahindra filters so I’ll stick with them

A buddy of mine who does a lot with heavy machinery, told me the same thing. I’m going back to the dealer today and returning the fluids and doing this exact thing. Do you know the cross reference for the Wix filters? Currently on the tractor is a wix oil filter but since it’s my first...

Awesome thank you for the information. I went on that link and printed out the manual. It’ll go a long way. I appreciate it! I’ll put my model number in the search bar and see what I come up with. I might still look for a service manual just to have on hand. Maybe somebody has a PDF file that...

Hi there, I just purchased a Mahindra 3510 3 days ago. I feel I got it at a great deal for $7000 with 1100 hrs on it. The machine is faded almost pink and not a show stopper but who cares on cosmetics! Anyways..I have a few questions I was hoping I could get assistance with. 1. It didn’t...