Search results

Just checked today. It's got exactly 4000 hrs on it. It's a 2001, bought it used in 2017 with 3000 hrs on it. So I've put 1000 hrs on it in 4 yrs. It gets used pretty hard most days. Lots of loader work. It's been a good tractor. It has a Woods 1016 (6') bucket on it with a quick change setup...

I spent a fair amount of time looking at the removal of the lines at the injectors. Considerations: Amount of "stuff" that would have to be removed to get at the lines, The possibility of injecting dirt into the injectors during the process. I used degreaser and air to clean the areas around the...

My TC45 (2001) started spraying diesel fuel out of the pump at the junction where the lines to the injectors attach. First, it was the leftmost and then the second one started spraying fuel. At first, I thought the plates holding the pieces to the pump were loose. After discovering these were...

Re-reading the post, I took a look at the TC35 link in one of the comments and noted it has the same issue as my TC45. I also noticed that the claim is that the Pentagon bolt is 9.5 mm which is impossible to find a socket for. The 10mm I bought appears to fit snugly. The bolts were tight and now...

My New Holland tc-45 with the Shibaura 4 cyl N844L engine developed a leak in the exact same spot within the last week. Was wondering if you ever got it fixed and what the repair was. I'm assuming there are seals around those ports that are toast. BTW, I bought a Pentagon 10mm socket on Amazon...

The steering on the TC35 at the barn where I work part-time failed on Friday. The wheel would spin freely with no resistance at all. Removed the column and power steering motor and found the end of the steering shaft to be stripped (rounded off). Called the dealer, over $150 for steering column...

Finally finished my sun canopy. Kinda copied Soundguy's bracket design. Used all "scrounged" material. Top was a piece of metal barn siding. Frame was from steel destined for the dumpster at work. Couldn't find nice pieces of wide 3/8" flat stock for the brackets so I took some curved scrap 4"...

Friend has an x300. Wouldn't start this spring. Popped the hood, no spark, wet plugs. Took off the motor cover. Noticed that 2 coils for the plugs had a small (14 or 16ga?) wire spade connected to them. Removed the 2 wires from the coils. It fired right up and ran like a champ. All safety...

Last year the Mighty Mule Gate Opener gave out at the farm where I occasionally work. Took it apart and determined the motor was shot. GTO (mfr) will not sell a replacement motor. They wanted to sell a remanned arm at a couple of hundred bucks. Couldn't track down the exact replacement from the...

From Detroit newspapers 10-27-10: A 47-year-old township man was killed Tuesday when his Ford tractor flipped as he tried to pull a stump. Deputies from the Oakland County Sheriff痴 Office were called to the 55000 block of 8 Mile in Lyon Township at 1:15 p.m., according to investigators. The man...

Need the plastic bearings for a binacchi pto guard. They're split rings and have 2 eccentric plastic screws on each end to secure the bearing to the guard. I found the Italian website for binacchi, but figure there HAS to be a distributor in the States. I've seen these on numerous implements...

OK, posted earlier how the tach on my "new" 3600 didn't work. Cable was missing. Bought a new one, installed it and tach still didn't work. Took off the cover and there was nothing connecting the top of the oil pump shaft to the proofmeter cable bushing. Obviously some parts missing. Looked up...

Bought a 3600 last week. Borrowed a brush hog to test it over the weekend. Everything was fine but..... Live pto clutch would not release. Could engage/disengage PTO lever WITHOUT an implement attached regardless of clutch action. Attached the brush hog and it would grind if you tried to engage...

Horse farm where I board my horse called tonite. Their TC45 would only inch along. It's a 12x12 transmission with FWD. It moves in LO, all 4 gears, F & R. Not sure if it's moving at the correct speed, though. But MID range it just barely moves and in HI doesn't move at all. I checked the fluid...