Search results

I can confirm the simple reset hold for 25 secs procedure works. Thank you all.

I'm ready to vomit. Just got a call...$15,000 to replace bad HST...8 year old tractor. I'm so disgusted. Like I said, I now have 2 Mahindras on my farm that had catastrophic damage. I don't even know what to do. I don't care how great of an experience you've had with Mahindra (I had 10 good...

I very much appreciate everyone's help and advice. Everything I try does not remedy the problem so off to the dealer it goes. One dealer just guessed that it's a failing pump at the cost of $10,000 and btw they're not available. I'm basically out of business. This is my second Mahindra and they...

Most likely 2 pumps since fel and rear hydro are working perfectly. I ordered a manual so I could at least understand the flow of the hydro drive. I feel like I've tried all I know at this point. I know there may be a hydraulic controller behind dash but if it's a sealed unit what can I actually...

Thanks for response Sergei. Sorry, responding so late. Yes hst and yes steering works. Ruled out all the simple things like rim rotation, remote lever in open position, clogged filters, bad oil, etc. I unplugged and cleaned the pedal switches under the floorboard too. I was really hoping it was...

Uhg. I'm reviving this post since it just happened to my "new to me" 2015 Mahindra 2555. Same exact issues. Tractor has been great for the almost 2 years I've had it. Worked fine all day. Powerwashed and parked it. Next morning the issues started. I thought I had gotten water in something but 3...

Thank you RAHarden. I ended up running over to my Mahindra dealer and bought their last ac compressor and fan belts - $21 each!. I install the compressor belt by loosening the adjuster and it went right in...15 minute job. I thought I'd quickly replace the fan belt as well but realized it was...

Any luck with this? My belt just blew. Shredded, can't even measure.

I slightly bent my left lift arm last year but didn't replace it. But last week while plowing snow with a rear blade, I snapped it in half. It got caught on a frozen rock and just broke in two. I asked my Mahindra dealer what the cost for a replacement would be and he originally quoted me $150...

Anyone have or heard anything about this mower? Got a price on 72" rear discharge for $1300.

Anyone know anything about the Craftsman 22.0 hp 50 in. Deck Riding Mower. It's $3000. I've had a craftsman for 6 years and I've beat the cr*p out of it and it's still going strong. But when looking at other similar zero turn tractors, they're more like $6000. Can't seem to find any user reviews...

Has anyone successfully used a rear grader as a plow?

Does anyone know of where I can get tractor tires online? A sharp piece of shale ripped into my front tire. I have a mahindra 2810. I have 25x8.5-14 industrial tires in the front. Any help would be greatly appreciated.

I must have some kind of leak. This can't be normal. My bucket very slowly lowers itself, even when the engine is running. I first noticed when I parked the tractor for the night and forgot to lower the FEL. Well, by morning it lowered itself. I don't see fluid dripping. Can this be a faulty air...

It whistles and wheezes on the up/down. I don't think I've noticed it this much before. Before I call my dealer and complain, I just wanted to know if this is normal. I don't think it affects the operation of the loader but I could be wrong. I could ignore it if I really try.

I seem to have a hard time switching the sub-gears on my 2810. It's just not a smooth change. Is this normal?

I was going to build my own dump trailer with hydraulic lift. But by the time I priced everything out and upgrading my tractor with rear hydraulics, I found myself back at the drawing board. Then I ran into this: www.northerntool.com - do a search for hoist kit. It took me about 8 hours. It...

I decided to make my own rake. Rakes are relatively inexpensive other than in NJ, but by the time I pay for shipping it becomes too expensive. I think the cheapest quote I got in my area was aprox. $600. So here it is. The steel came from local scrap yards - aprox $30. The tines were $2.99 each...

Has anyone purchased or used or seen or heard of a Kodiak box blade. Got a really good deal on a 65" box blade from Agri-Supply for $277.95. It's 416 lbs and has 5 adjustable scarifiers.

It's still in progress. I'm sure now that I've built it, it won't snow. I'll put a hydraulic valve on in the fall. Right now I just pull the pin to rotate the plow. I'll put a strip of rubber horse mat at the bottom to absorb impact from stones or such (as someone else did on this site - thanks...

Since this is my first tractor, I would have no idea if this is a normal occurance - my FEL contoller is "frozen" in place when I start up the tractor in cold weather (teens). It takes about 20 minutes before I could wiggle it into operating mode. Is this a Mahindra (2810) problem or is this...

Has anyone built a plasma cutting table similar to image attached?

I will be starting a barn/workshop project this spring and I've been wondering...to permit or not to permit? Just wondering what you guys have been doing as far as building permits, and if so, how were your taxes affected.