Search results

TN75 - Does anyone know how to eliminate joystick excess play when connected to the rear remotes?

The problem was the seat switch, the tape came off. I knew it was taped closed (previous owner let me know that). If you shifted the shuttle lever into the center the clutch pedal would need to be pressed to go again. If you do a quick shuttle directional change you do not need to press the...

Thanks Rick. I will check those two things out. I was under the impression that my seat switch had been previously bypassed (if that is possible).

Interesting. When first moving from a standstill I was always required to operated it by needing to press the clutch pedal or otherwise the alarm indicator will flash (and it would not move). Now I can drive anytime without ever using the clutch pedal? Could be dangerous if I accidently move...

Good day all. Under normal conditions with the tractor moving I can change the drive direction using the power shuttle lever without stopping and without pressing down the clutch pedal. I noticed now that if I move the shuttle lever forward or reverse from a stand still the tractor will start to...

Took it apart last week and disassembled it and put it back together and it works fine now. I see there is a 90 degree cable connector from the cable to the back of tack. There seems to be a lot of sloppiness in that area. So the cable is not broken but I suspect it will come back and at that...

Thanks for the info, I took a quick look today and I can see what looks like a mechanical cable coming from behind the instrument panel to the mid area of the left side of the engine (drivers side). I will call the dealer to see what is available to purchase.

Good day all, Yesterday on my TN75 when I started I heard a little bit of a different startup noise. I did not immediately notice anything wrong but later I noticed that I lost my RPM needle & hr meter. Is it common for this to happen? Has something disconnected or did the cable break? How...

My TN75 is M20 x 2.5. I did the same thing to install a 2" receiver for my winch.

Can I ask why you would add biocide to your diesel fuel? Under what circumstances and frequency?

Thanks for the info. What type of FEL control is on this tractor?

Good Day all, So I finally got my winch installed and operating on my TN75. It works great, and FYI I just use it occasionally to pull out the far away and hard to get at log. Even then, I don't do a constant pull. This NH model has a Power shift which means I can forward/reverse without...

Well I am sure this has been beaten to death here, but since I am relatively new here, and the cold weather is here I thought I would ask about diesel fuel conditioners and additives. I don't generally put on many hours (NH-TN75) in the cold weather. My first question is are they really...

Hello All I have a wireless remote 10000 lb winch on a 2" hitch that I can use on my truck and on the rear of my tractor (3PT hitch 2" receiver). I am planning on building a 2" receiver on the front of my TN75 NH tractor for dragging out logs in the woods. My 2 questions are, am I in danger...

Good day all, My NH TN75 Stoll FEL (new tractor to me) is connected to the rear remotes which is controlled with the joy stick. Currently my manual third remote is not being used. (I have a hydraulic blade and may use it for a grapple some day) With my current setup, I do not have and miss the...

Good Day all, I am considering picking up this tractor with 1800hrs. It is 4x4, has the hydraulic shuttle & FEL, open station, I am just looking to hear from anyone that has encountered any problems with these tractors. It looks like it has the Iveco 3.9L with mechanical shuttle. It will not...

Good Day all, Today I test drove a M7040 with about 1800hrs. It is 4x4, has the hydraulic shuttle & FEL, open station, 1 set of remotes being used for 3rd option for FEL and not loaded tires. (Not sure of the year) This dealer here in Canada is asking 36K (26K US) for this tractor which I...

Hi There, My case 385 MFWD has 5900 hrs. It seems that it could have a little more power. I notice on high gear on high range that I cannot completely let out the clutch otherwise it will stall. I need to ride the clutch a bit until it gets up to speed. Also notice on start up that the...

Hi There, Does anybody know the Front/Rear drive train ratio for this 4wd tractor? I want to get new tires and want to go one size larger on he rear. The manual allows it as an option. Currently I have on the front 8.3-24 and rear 14.9-28 and I want to put 16.9-28 on the rear. Will I be damaging...

Thanks for your help. Yes the trouble shifted to the bucket when I connected it to the left spool. Also put a pressure gage on both sides of the lift cylinders for the left spool and the pressure gradually increased on both sides till about 2000psi or I stopped it cause it was loading the...

Hi There, I have a Case 395 with a Cross 2 spool hydraulic valve. The problem I am having is that when I am raising the loader using the left spool lever, at about half way up it stops and the it loads up the tractor hydraulics. If I put the loader up hoses on the other lever (Bucket dump) it...

Hi everyone, I am in the process of retrofitting a loader onto this tractor. I need some help with the hydraulics. There is one set of remotes on this tractor and it is an 89 vintage 4 x 4. Specifically I need to know where to get my supply for the loader valve. I think the return goes to a port...

Hello everyone. I am considering buying a 1991 CaseIH 595 4 x 4 with loader and with 3200hrs open station. My question is, is this a good tractor? I plan on using it as a utility tractor and for bush work. It seems to run well. Also what should be the going price. He wants $17K for it. Thanks

I am going to be building my own log splitter. Has anybody ever bought this cylinder or seen it on a logsplitter? -> Burden Sales Surplus Center Item Detail <- It is an excellent price but not sure of the quality as well as how to build the base plate mechanical setup. It is an unusual port...

I am going to be building my own log splitter. Has anybody ever bought this cylinder or seen it on a logsplitter. -> Burden Sales Surplus Center Item Detail <- It is an excellent price but not sure of the quality as well as the base plate mechanical setup. It is an unusual port...

Hi all. Just wanted to show you all my latest bullds. I am now working on a rear ballast weight. AutoCad was my best helper for the FEL. As you will notice in the pics I also built my own snowblade for the front. I built it so that the rear 3PTH control raises the blade up and down. It works...

Does anybody know why these small diesel engines on these tractors idle so high? (above 1000 rpm) Small diesel engines in autos idle at much slower rpm and are therefore much quieter!

See other post

Well here it is. Been working at this since last fall. Still have some finishing touches to do. QA forks and rear counterweight are next. Click link below for pics.

I have a BX 1850. Does anybody know if they can handle boosting a car. That need may arise sometime and just wanted to be prepared. I do not want to damage something. Thanx

Has anybody had any experience using a Bota BX front mount broom/sweeper attachment for lawn sweeping in the spring. Been thinking about picking up a used one for a good deal but wondered if they did a good job on the lawn. Thanks

Has anybody had any experience using a Bota BX front mount broom/sweeper attachment for lawn sweeping in the spring. Been thinking about picking up a used one for a good deal but wondered if they did a good job on the lawn. Thanks

On my BX, I am plumbing in my loader valve. I am using 3/8"OD steel tubing lines with .035" wall. My question is do I need to double flare the ends? I am planning on using a single flare. Will that be sufficient? thanx

Hi all. Iam trying to plumb a 4 way husco FEL valve to my BX. Attached are some pics of my tractor and the valve Iam trying to connect. Also included is a pic of a new tractor line connection with the ports marked A, B, & C. What I need to know is which port from the tractor goes to which port...

Hi everyone. I have recently purchased a used 45 ton ironworker. I want to construct my own brake dies. Does anybody have any experience building a brake V-block and blade or where I can find such info. I am currently building a FEL for my BX1850 as well as many future attachments and this...

Hi everyone. I have recently purchased a used 45 ton ironworker. I want to construct my own brake dies. Does anybody have any experience building a brake V-block and blade or where I can find such info. I am currently building a FEL for my BX1850 as well as many future attachments and this...

Hi everyone. I have a BX 1850 and when I turn the key to run position (before starting engine) there is some eratic clicking noises from the underside. Is this the diesel fuel pump?