Search results

Where can I get a replacement Spin on hydraulic filter for the 336D? And what are the part numbers. Thanks, Mike

Here it is a pic with the YM2000 my buddy bought from me with the 93" finish mower on it. By the way he just cut his grass in 7th gear @ engine 1800 rpms. Claims it did not have any problems lugging down.

My buddy that purchased my old ym2000 after I got the Ym336D, and he bought a Del Morino xrm235 finish mower (rear discharge). He thought it was a 6' mower when he went to get it. It needed 2 pulleys fixed and I just finished that. I mowed with it today - That is one big mower. It was...

FYI tractor supply selling generic 303 for 24.99 5 gallons

Can someone tell me what kind of loader is on this tractor? Thanks, Mike

Does anyone know what it would take to add hydraulic rear hookups to a 336D?

I disconnected my FEL and now my rear lift is not working. I am sure its something simple but I can't figure it out. I'ts a 336D

Ok, I can not seem to make up my mind on the color of paint for the FEL. It is red now, but either way I am going to have to re prime it. So, what do you guys think RED or BLACK ?

Fixed the rust on the fenders on my 336D painted the back half of the tractor while I had everything off.

Does anyone know how to enable the creeper gear on my 336. There is a lever next to the 3 speed on the floor that is for it. But when i switch it to the side it just springs back into place.

I think the fender on my 336D is the same fender off a jd 950. Can anyone verify this? I have been looking at closeup pics on the internet of the 950 and it looks identical.

The head on the 336D I just purchased is a 3T90T-J. Does this seem normal? Here is a pic

I have searched around the site. I need to know what fluid to put in the front axel of the 336D. Thanks, Mike

Does anyone know what turbo brand/model is on the JD 1050. Thanks, Mike

How much is a 336D worth - needs a front bucket and one fender. Thanks, Mike

Ok, I finally got all the parts in and put it together. I am running a TD04-9b off a 93 Turbo Stealth (just one of the 2 turbos). I am running about 3-4 psi under boost. I actually think the gasket is leaking on the valve cover causing loss. I will take a look at it later.

What is the engine size in Liters for a YM2000? Thanks, Mike

I have both a YM2000 and a YM1700. The YM2000 seems to be louder than the YM1700. Does anyone know if this is the case?

Here is a picture of the piston I pulled out of my engine today. The rings looked really good but part of the piston was broke inbetween the top two rings. I think this may be my hard start and lugging problem when taking off from start. What are your opinions?

My YM2000 is hard to start, but seems to be fine after its started. I have tried the valve relief and let go after turning but is still hard to start. Once I start it I only get a puff of white smoke when I hit the throttle and that is it. I have a YM1700 also and it seems to start really...

Has anyone used a cultivator with their YM1700 or YM2000 to cultivate between rows in your garden to get rid of weeds? If so what is your row spacing? Thanks, Mike

I just purchased a YM2000 from an indvidual. The right front wheel is tilted in at the top, and I can not figure out from where. It does not appear that the front axle is bent. What else would I look for? Thanks for the help I got a good deal, and I knew about the tilt when I purchased...

Has anyone put a slip clutch on a RS1400 Yanmar tiller? I am looking at the one at Tractor Supply, an was just wondering if it will fit. It looks like it might be tight. Thanks, Mike

I took off my oil pan for the 1st time to make sure everything was good with the motor. (I know they sound like a hammer) But being my 1st one I wanted to make sure the rod bearings were good no play. It looked really clean and everything was good - ie no worn bearings. I just wanted you...

Does anyone know how many hours a YM1700 will run at working speed on 5 gallons?

This is my YM1700. Wish I would have taken a pic before I stripped and painted it. Very Dull brownish red paint. Not too much rust on the metal though.

This is the first time I have used it for the garden. I have a RS1400 tiller to go with it. It did the work great. And having the faster pto speeds for the 2nd and 3rd pass made the dirt very good to plant in. I have a 1700 (newly painted)

I just finished repainting the hood of the tractor but now I need to find out where to get the decals for it. I will need the whole set, as I am in the process of stripping the fenders and dash. Thanks for the help, Mike

I am missing my overflow bottle on my 1700. Can someone post a pic or email me one of it installed? Thanks, Mike

Here is what my 1700 sounds like. Let me know if it sounds normal. This is started in 55 - 60 deg temp tonight. http://nesh.net/tractor_sm.wmv

I put in some manual guages and I am trying to figure out what the values should be running. What is the oil pressure supposed to run on a 1700 that is at running temp? I am getting 45@ 1000 40@ 1500 50@ 2200 Also, how hot should the tractor be running? I am...

I have just purchased a YM1700 and it seems to sound like it has a loud knocking noise. Is this normal? It does seem to almost go away when you run it up past 2000 rpms. Thanks, Mike