Search results

Today, my tractor overheated about one hour into bushogging. I use it very infrequently and it seemed to run hot the last two times I used it. Nothing I did (cleaned radiator seemed to help). I limped it back to the trailer and on the way it wouldn't hold at a high rpm. It would smoke and bog...

Hello, Do ya'll know of any reliable Mulching Contractor's in South Central La.? I have approximately 2 acres (~ 30ft x 2900ft) of fence line I would like to mulch. My property is located between Opelousas and Ville Platte La. Thanks,

I found a Ford 535 with loader, but no PTO or 3-point for $4800.00. Not sure on the number of hours. Condition is good. Is this a good deal? What should I offer? Can I add a backhoe w/o a PTO...

I have a steel power steering line that consists of the line, a compression fitting, and a barrel nut. The line connects to my steering box. The problem is fluid is leaking from between the line and the nut. I've tightened the line, but it still leaks. Any repair tips other than having to...

Does anyone know of mulching contractors that work in in south central louisiana? I have 14 acres worth of overgrown property lines to mulch this spring. Thanks,

After changing my starter solenoid and ignition switch trying to figure out why I couldn't start my tractor ( Mahindra 485DI). I finally found the culprit. A wire was broken internally. It was the wire from the solenoid to the switch. I put in a new wire and it fired right up. Maybe this help...

My 5ft cutter deck has a few holes in it and I am thinking about re-skinning the damaged areas with 1/8 steel plate. The question is....do I weld the new sheet over the top of damaged areas or not??? Is there any issue with layering the sheets in this manner??? Thanks in advance.

I removed my POS Lucas Starter Solenoid from my Mahindra 485DI tractor. When I removed the soleniod the rear portion of the solenoid stayed in the housing next to the starter. There's a rod from the starter that is held to the end of the soleniod with a spring. I had some trouble removing the...

Can anyone tell me what the correct valve lash should be on a Mahindra 485DI? Unfortunately, I don't have a service manual for this tractor.

I have a Mahindra 485DI that has 30 pounds of oil pressure according to my gauge. Is this the correct pressure or is the oil pressure weak? Thanks,

What's the best body filler to use? I have some dents pounded out and need to fill and sand them smooth. Is tractor vibration an issue with Bondo etc. Any help would be appreciated.....

I noticed a bit of squeal in my hyd. system and I want to change/clean the hyd. filter(s). How do you do this? Thanks,

I am about to paint my tractor and need to fix the area under the front grill (badly dented). What tools and techniques do I need to straighten out the dents? I'm no bodywork expert. Can this be done without purchasing specialized tools? Thanks in advance

When replacing the two fuel filters on a Mahindra. I assume you change one at a time. Do you loosen the bolt at the top center of each filter to remove the bowl? Are there any pitfalls to be aware of? Thanks,

I'm buying a Mahindra 485DI for $4850.00 (tax included). The S/N is 2487. Can anyone tell me the year of this machine? Are they good, solid machines? Thanks,

I saw a 610 Long that needs an engine. The one that's in it is bad and needs replacement. Any idea where an engine can be found and what a reasonable cost would be?

I tried to repalce the PTO seal on my YM226 and when I pulled the PTO cover off a transmission assembly came out with it!!! I put it back together and now the PTO won't disengage. It stops turning with the clutch engaged. Under load as the PTO shaft slows down you can hear a clicking noise...

I need new headlight assemblies for my YM226. Has anyone found an off the shelf headlight that can be used on our Yanmar Tractors? I figured there had to be a generic headlight assembly somewhere. Yanmar is real proud of their parts. Thanks,

I was bushhogging 10 acres for my Dad last weekend and I forgot about a lowlying area and before I knew it I was sinking. I picked up the bushhog to no avail. I was stuck spinning the rear tires of my 2WD Yanmar YM 226. I was in Mid range / high gear. I question is what could I have done to help...

The Wiring on my YM 226 was trashed when I bought the tractor. All the safety devices have been defeated and the horn, lights etc. do not work. Does anyone have a wiring diagram and helpful instructions for fixing this mess. Am I better off trying to re-wire the tractor or should I just cobble...

The tachometer cable on my YM226 bolts to a small fitting on the front of the engine block. The fitting is right next to the fan belt and appears to be held on with two bolts This fitting is leaking oil almost continuously near the lower bolt once the tractor is warm. How do I fix this oil leak...

Guys on the left side of my YM 226 below the oil filter there is what appears to be some sort of sensor. It is round and comes to a point (facing toward the radiator). The pointed end has a brass appearance. What is this for and is the brass pointed end supposed to be exposed? Thanks,

What\'s this line for???? I was doing some boxblading this morning and I noticed some oil on the side engine panel of my YM226. I pulled the panel and the bottom side area of the radiator was wet with oil. There is a small line that goes from the radiator to the side of the engine block( not...

Well I pulled the trigger and bought the YM 226 that I was looking at. I bought the tractor and bushog for $3500.00 cash. The only thing that I found other than non-functioning headlights is the valve cover gasket leaks a little oil. I have a couple of Yanmar newbie questions. Is the valve...

I found a 2wd YM 226 w/ ROPS in good condition with 541 hours on the meter. The tractor comes with a bushhog (minus the shaft) for $ 3950.00. The tractor is located in Louisiana. I plan to go and test drive the tractor this week. Does this seem like a reasonable price?

Guys, I also looked at a 1965 model 3000 that has a newly rebuilt engine, new tires and good paint for $4500.00 firm. The price includes no implements, just the tractor. It runs and drives good, it smokes white at idle then clears up at higher RPM's. Does this seems like a reasonable price for...

Guys, I'm in the market for a Ford 3000 tractor and I need a little help. I looked at an English model 3000 tractor with 6500 hours for $4350.00. I need to know the year model and if the price is reasonable. The serial number is A226248 and is located in Louisiana. Any help and advice would be...

I've been researching grey market Yanmar Tractors for a few months and I must say that this forum contains a wealth of knowldge. Can anyone reccomend a dealer in Louisiana/SE Texas? Thanks in advance