Search results

Thanks for the input. The hold down bolt(hook)s seem plenty adequate in the pictures sent by Gordon for his 87/8" battery height. Either his bolt(hook)s are longer than mine or I didn't measure correctly. I extended mine to the end of their thread and it looked like it only raised the hold...

My current battery is a Group 24N and 13 years old. It still starts the tractor good, but I want to replace it before cold weather is here so it doesn't let me down when i got a pile of snow to move. I discovered that I can't buy a Group 24N battery anymore and all the Group 24 automotive...

I have a Lincoln Pistol Grip gun with LocknLube coupler which I bought separately. The coupler works well where you have room to use it, that's not always the case. I grease my mower deck spindles without removing the deck. I don't have enough clearance above the center spindle to use the...

I just sprayed my driveway on both sides, the center is paved. I used Grass and Weed Killer, 41% Glyphosate at 3 oz. per gallon with an 1.5 oz per gallon of 24D just to give It a little extra kick. It's very effective. The 41% Glyphosate is from Home Depot. I got 2.5 gallons for $105. A...

I would say you definitely have an adjustment problem. I have 32 HP tractor with a 5 ft. tiller from Tractor Supply. I and my son have worked up quite a few acres of sod that had probably 10 years to establish itself after the farmer renting my property went bankrupt and left all my fields...

I have a Kubota L3010 with an Erskine 60" pull behind blower and I believe something like 28 PTO HP. So far the pull behind blower has worked well for me, but we haven't been getting too much snow and I use this on a 1/2 mile paved driveway so I don't need to worry about picking up stones. If...

The PTO drive belt jumps off the right hand idler pulley where the belt makes the turn from vertical to horizontal at the front of the tractor when I engage the PTO. This hasn't happened every time I engage the PTO, but often enough that I burned up one belt after it jumped off the pulley and...

I'm coming in a little late on this thread, but wanted to report a couple aspects of my newly purchased XT3 GSX that I'm a little disappointed in. I have a country lawn that probably needs some roller applications, but as of now, it's quite rough. The ride on my new mower is very harsh. I...

A week or so ago, I posted a rather negative review of the FEMCO Weather Brake during my installation of this enclosure and after I had inquired if anyone had any comments on this accessory. Response was minimal which I think means that this old style enclosure is not very popular. In all...

I got a Weather Brake heater enclosure for Christmas for my Kubota L3010. The instructions are not very good because some of the pictures of how the parts are to attach to the tractor are pretty poor. Does anyone have one of these on their tractor and if so, how do they like it? I think we...

I have an Erskine pull behind snow blower with a Urethane cutting edge. I'm on my 3rd winter with this unit and I'm noticing that the edge is wearing a concave dish right in the center portion of it. It's about 8" long and a 1/2" higher, than the rest of the blade, right at the high point of...

I have an L3010 with 875 hrs. The owners manual says the valves should be adjusted at 800 hours. How important is this to have done if the tractor still runs well? I have no trailer to transport my tractor to a dealer, so this will likely be an expensive adjustment if I need to have it done...

I have a question for those of you that have a Glide Shift Transmission. I'm learning how to use a pull behind snow blower for clearing my driveway/parking areas around the house in addition to a long driveway. In the area around the house it would seem that the most efficient way to operate...

I have a L3010 tractor with 420/70-24 rear tires. I'm considering loading these tires with Rimguard Liquid ballast which will add about 600 lbs. to each tire to give me better traction when plowing snow with a rear blade. I have a 1/2 mile driveway. I'm a little hestitant to do this as I'm...

I have a Woods 6' Rear Finish Mower and the grease fitting on the universal joint next to the gear box has loosened. I can't get at it well enough to tighten it with the protective shield in place. I need someone to tell me how to remove the shield over this universal joint. I'm hoping it...