Search results

Thanks for showing off your stack. Now, how many ways could you bolt the manifold to the lift cover?

It's just the factory valve that bolts to the hyd top cover.

Hey, I'm having the hyd hardline from the pump to the right footrest blowing out at either end after I installed an hyd remote assy. I am assuming that somehow the hyd pressure is deadheading and pushing the line out of the rubber compression fittings. Maybe the spool is stuck? I have qorked the...

Thank you. I will try this on Thursday afternoon when I get back down to the farm.

Also, the PTO clutch seems to be out as the PTO will not turn when the clutch is released.

Bought a Ford 2000. Has a bit of blow by so I’m easing into this project as I am not sure what the engine condition is. It runs well, drives well; but the 3 point lift only raises 8 inches at the pivot balls. The lowest level is 14” and it raises to 22”. Is this a normal lift amount? I...

Detent plungers rusted in place. Left-most fork shaft rusted/frozen in place. Thank you!

Understood. The balls and springs for the detents are in the rear of the cover? Thank you.

It’ll be a few days before I get back to the tractor to look at it and hopefully the service manual will arrive by then.

Thank you! It was a loader tractor (loaderless now). I bet it saw a lot of fwd-rev shifting. Much appreciated!

No, will not go into gear when not running….

Hello, I just picked up a ford 2000 3 cyl at auction. This tractor will not go into gear. I have not pulled the transmission top cover yet to look at the shift forks. I spoke to the previous owner's brother who told me that he did pull the cover and saw nothing out of the ordinary. If...

Re: Kioti LK3054 Alternator 敵eneric Replacement Hopefully I added a photo. RF

The direct alternator replacement for a Kioti LK3054 is the alternator for a 1979 Mazda B2000 truck. This alternator is a Mitsubishi and is identical down to the 4 pole pigtail plug. (You might need a shorter belt, however the belt on my tractor may have been plenty stretched due to it being an...

The voltage dash light on my LK3054 is either flashing slow or intermittently coming on. I've read through some posts here and there and seems it may possibly be a voltage regulator. Has anyone any tips regarding this? Thank you.

A little modding to fit this tractor.

Is this correct?

I bought a used Kioti LK3054 as a chore tractor after Thanksgiving from a Kioti dealer The water pump went out about 20 days after I bought it, and I ordered an OEM water pump from the dealer I bought it from. Now the starter has a short circuit. The water pump was just under $300 with gasket...

This is a picture of the infeed roller that the mechanism is lifting. This roller it turning so that the top of this toothed drum is turning toward you as you stand at the back of the chipper, and the bottom of the drum is pulling the branches under it into the bladed flywheel. It is under...

Here is the progress. I can provide measurements is anyone is interested.

I have had a couple of these over the years. Bought them on Craigslist and then sold them later as they are a bit of a boat anchor when you are not using them. They take up a lot of room and are awkward to move when not on the 3 point hitch. I finally got around to cleaning up the dead ash...

Hello, I will be evaluating a Mott Flail Mower with the 4 rows of knives. They are the long Y knives. What should I evaluate when looking it over? Do the Mott mowers turn the blade drum in the same direction as the tires on the tractor. If so can the blade direction be reversed? Is there...

Removed rear seat stud to fix threads on my Ford 3000. Seat was loose and I thought I'd tighten it up. Now however, the 3 point arms lift very slowly, and will not lift an implement. I am gathering from reading posts that it has something to do with the draft control plunger. Can anyone shed...

Bought a Ford 3000 that seemed to have a bad Simms injection pump. Pump runs tractor but hard to start, governor slow to respond, oil reservoir filling with diesel, low power under load. I pulled the pump, and removed the timing cover because the marks through the IP gear cover were not lined...

Looking for some input on a Simms to Cav Injector Pump conversion on a Ford 3000. Simms pump governor is lagging and diesel is filling the oil reservoir in the pump. The local ag salvage yard is very helpful and great to deal with. They do not have a good used Simms available but do have...

I just bought a used Yancheng WC-6 wood chipper. Any areas to examine on this chipper before I put it to use. I've read most of the posts on Chinese chippers, I'm just not sure what the difference is between Yancheng (2004) and Jimna etc models. Any pointers/tips would be greatly...

80 hrs on new CK35 2010. Changed fluids at 50. No Problems. Working it HARD!

Owned a lot of tractors over the years. Downsizing and bought a CK35 as a utility today. Do y'all have any concerns or pointers for me when breaking in a new Kioti. I'm used to the Red or Green brands, so hopefully this Orange one will last at least as long as I have a use for it- 10 years or...