Search results

CH4, Good idea, I might try that. I finally got a parts guy that knows what he is doing and he ordered one. Hopefully it is the right one. Thanks all for your suggestions. JPC

Been There, Thanks for your reply. The link did not show the line. The model loader is 400R with full (6) connectors. It is the lowest line one the disconnect plate from the tractor to the loader. The other end is the second from the front on the block underneath the right side of the...

Been There,

I split the hydraulic line again. I repaired it with silver solder but I need to replce the steel line. I cannot find the individual line on JD parts. It is the curl ine for the bucket. It goes from the block to the loader. Can anyone tell me how I identify the part number? JPC

Since we are talking mower blades, does anyone know where I can find a left hand (CCW rotation) blade equivalent to Oregon 396-612 specs? This is for my finish cut AMF 4214 Landpride mower. IMO, The OEM blades are not beefy enough for the machine. I have searched high & low and I just can't find...

Happened when I was curling my stump bucket. It was about an inch long, looked like someone sliced it with a razor. I had already done the heavy work removing the stump. Has anyone ever had this happen? I took it off and closed it back up and silver soldered it. Works fine.

I have added a 3-5lbs PSI inline fuel line pump to assist fuel getting to injection pump. Cleaned pick up screen on intank fuel pump. The leak is on the high pressure side, it should not be affected by supply side pressure. I have new OEM O ring seals for top fittings on order. I just replaced...

T, try it now J

T, Attached you will find OEM number on second page. J

T, The mower is a 2017 Landpride AMF 4214 batwing finish cut pull behind mower. I want something heavier than OEM blades. The OEM blades are listed in the attached description for the Oregon blade 596-627. This specs out pretty close. Also, I like Oregon 396-612 because it is a little thicker...

Yeah, I been trying for several years to find heavier LH blades for my Landpride batwing finish mower. Stock LH blades a just 2" wide and don't have the force I am looking for in heavy areas.

I am looking to find a left hand cut or CCW rotation mower blade that has the same specs as the attached file. Could someone please point me in the right direction? I just am unable to locate one. see attached files showing specs of Oregon 596-627 Thanks

I would like to add an additional step to my 2010 4720. Looking for a good link that has a bolt on additional step.

Turbocharger & exhaust manifold are white. Should I replace my turbocharger? JPC

I have checked rear remote scr's & none are stuck. This just seemed to happen after I got into some real heavy grass and did not ease up right away. I have used it since and it runs ok until I get a load on it. Then it hisses like fluid is bypassing a port and also the engine pours out black...

john deere 4720 pto hissing sound. any ideas?

Where can I find a CCW rotation gator blade or equivalent for Oregonｮ G5 Gator Blade 20-15/16" Length / 596-627? I called Oregeon corporate and they do not make them. I need these for my finish landpride 14' mower. I would like the heavier blade than what is offered in stock model. JPC

Preheater works but indicator light doesn't. Last six S#770631. Any ideas?

Where do I find TM2370CD for my 4720 serial #770631? The highest number available is up to 650000. JPC

Where do I cut into hydraulic lines to add another hydraulic port to my 773 Bobcat? JPC

After trying to push over a tree my 773 hydraulics won't work. I think I must have jiggled loose some wires in the lockout system. Any ideas where to start looking? I'm thinking seat & steering sensors. JPC

Does the John Deere Filter Kit LVA14896 include the a/c cab air filter for the 4720 CUT? JPC

I have a 2010 4720 with power beyond. I would like to purchase a 3 pont hitch backhoe attachment for this tractor. My question: What would be the largest model/size 3 point hitch backhoe attachment that this tractor have enough power to operate properly? JPC

Any ideas what to make side extensions for my 7' wide front blade on my 4720? I would like it to extend to 8' and retain the same curvature as the molboard. JPC

Could someone post a picture of the 400 CX front mount on a 2010 4720? I am trying to see if I can attach the 400CX over my existing fabricated mount for a 7' wide blade.

How difficult is it to install? Anyone have instructions on how to install power beyond on 2010 4720 w/cab? Can I purchase it from another source than my dealer? JPC

I am thinking about purchasing a 3455 Splitfire 3 point hitch logsplitter. I also want the hydraulic loader that goes with it. I assume that I will have to install power beyond on my 2010 4720 Cab tractor. Does anyone have experience with this particular setup that they could share with me...

I am thinking about converting a 16 ton gas engine powered log splitter to a 3 pth mount powered by rear scv. My question: Is there enough of a hydraulic flow rate on the stock 2010 4720 cab unit to run it reasonably fast? JPC

1999 455 (2100 hrs plus) lawn tractor not starting (in cold weather) like it should. I'm thinking glow plugs maybe dirty or worn out. Does anybody know if they loose their heat value over time? Could I just take them out and clean them or should I replace them? Is it time to have the injector...

Has anyone tried using a hydraulic hammer as a wood splitter? I think using an asphaly chisel in the hammer might work. Any comments? JPC

What color is the low fuel light on a 4720 w/cab? I show the gas pump icon lite in clear light along with the full mark & engine coolant mark. I have not noticed it since I bought it in July of 2010 and thought it was a warning light but it might be normal. Can someone tell me when the low fuel...

Stopped to fuel up. Restarted by cannot move machine or raise/lower bucket. How do I unlock machine? When I turn on the ignition switch, I do not he the second click that I normally hear before I start up. JPC

The low fuel indicator light came on while I was operating today. I topped off the tank and it stayed on. Any ideas? 2010 4720 w/cab JPC

I currently use Mobil 1 10W-30W in my (2010) 4720. Mike told me I should use Mobil 1 turbo diesel truck 5W-40 fully synthetic motor oil. I've researched it and it looks like it is the right selection for my 4720. Does everyone agree? JPC

The manual says: Every 400 Hours Change engine oil and filter (if John Deere PLUS-50 is used). Change transmission oil and filter. Clean transmission suction screen. Replace fuel filter. That seems like a long time for the first change. Any comments? JPC

I have a new 4720 w/cab with a diverter switch to toggle between the front & rear SCV. I noticed there are three positions on the switch. 1. on: activated which illuminates a red light: activated, (rear SCV operational) 2. off, flush with switch housing: deactivated, no light (front SCV...

I was using my 773C today & all of a sudden I noticed the tilt cylinder on my grapple bucket leaks down real fast. My question is how do I determine if the problem is the cylinder or the valve body? JPC

I need an angle ram (swing ram) for a John Deere 84" M# 3680M front plow. John Deere wants $450 for a new one. The one I have leaks real bad and piston head is stuck in place. I have had it looked at by two different shops and they said they can't do anything with it. I am going to try and get...

I need a hydraulic angling cylinder for my 84" front mounted blade. The model number is 3680M. I have not been sucsessful through John Deere. Any suggestions?

Am I ok running #2 heating oil in my new 4720? I've been doing it for years in my International Lowboy I2400D with no trouble. I would like to continue with my new tractor if it makes sense. JPC

I am looking for the left fender for a 1969 Ford 5000. It is the clam style. Darell

KennyD, Could you walk me through using the JD parts page on the internet? I have used it a little but would like to understand it better. I need to be able to pull up the illustrations of the parts with the part numbers tec. JPC