bolens g154

My G154/TX2140F is grinding gears when I need to change gears. Same thing when changing from high to low on the transmission. I can quickly change gears from one to another, but beyond that, I shut down the engine when shifting. I adjusted the pedal travel with no change and am thinking I...

The best that I can tell is that the stock rear 16-inch wheels are approx. 5.5 inches (140mm) wide and the 12-inch front wheels are approx. 3.14 inches (80mm) wide. The tractor comes with 8-16 and 5-12 tires. Does anyone know if 9.5-16 tires would fit the rear rims and 6-12 tires the front...

Hi, I'm George from UK. I've been lurking here for nearly 3 years it seems. Probably about the same amount of time I've owned this tractor. I've finally started to take a bit more care of my tractor rather than just abusing it. It's a great machine. Any tips relating to manuals, procedures...

Hello all - I mentioned in my introduction that I have recently purchased a Bolens/Iseki G154. I got it from a guy who never used it, and knew little to nothing about it. I have a few issues I could use some input on. I'll go through them one at a time. When in low range, the tractor will grind...

Hi all. I recently purchased an Iseki Bolens G154 with 4wd and 15kp K3A engine. It is in great running order with only 400 hours on the clock. I am looking to do a mini restoration on it and want to add implements etc. So looking for information. Thanks.

Does anyone know what kind of seat that will fit my Bolens G154. I have looked all over the internet but can not find one. Thank you.

Does anyone have a pic of a front PTO setup on a Bolens/Iseki G154? The splined PTO on the front of the engine is so close to the radiator, how can anything attach to it? where would the clutch sit?

Found a pretty cheap Bolens G154, so I thought I would take the leap and buy my first tractor. That was easy part, now I gotta figure this thing out. :laughing:

Hello everyone, My first post here, and hoping you guys can help me better than google has been. I recently purchased a set of front tires for a Bolens G154 (Iseki TX1300 I believe). I got the right size (5.00-12) but the lugs weren't quite right in the picture, oh well they are the right size...

i have a bolens g154 with 2 stage blower. does anyone have advice on rpm range,what gear? any help would be great thaks

Hello. I am looking for a Drive Set Gear (6) (front ring/pinion) for a Bolens G154 Compact Tractor. The manual I have says the Parts code is 1871481 and it has another parts code that reads 1427-043-2000-0. I also need a pinion seal. Can any one help please. Thank you. :)

Looking for information on turf tires and wheels for my bolens g154 iseki tx1300f.

Hello. I am looking for a Drive Set Gear (6) (front ring/pinion) for a Bolens G154 Compact Tractor. The manual I have says the Parts code is 1871481 and it has another parts code that reads 1427-043-2000-0. Can any one help please. Thank you.

Hello, I did some work on a co-workers boat and in return he gave me a Bolens Iseki G154 tractor. He bought it last year to fix it up but boats are now taking his time. The tractor will not start. It turns over but he was told the plungers for the injectors are stuck. Also the clutch disk is...

I am looking for 2 oil seals for a Bolens G154 / ISEKI TX1300F. One for each side of the 3 point hitch arms where the arms go on to the splines on the tractor. Does someone know where I can find them. Thank you.

My diesel fuel line from the tank to the fuel filter/bowl was snagged by a branch and broke. I did not notice and the tractor ran out of fuel. I repaired the line, filled the tank, opened the bowl to remove any air, bled the low pressure line to the injector pump and cracked each high pressure...

Hi, I have a general question if anyone knows the answer, because I have not been able to find a ton of information in my repair and operators manual. I have not changed the hydraulic fluid in the rear of the tractor since I have owned it. The manual says that there are three drain holes, and...

I just needed a bit of advice if anyone knows about the 4wd front gear case. case. There is one on each side, and there is a grease zerk on the top. I believe the grease goes into the socket that hold the front arm that looks like a silver bowling ball, I think its called the king pin...

Hi, I am new to the forum, and its great to meet everyone and see that there are fellow tractor owners/enthusiasts on here. So I have a Bolens G154/Iseki TX1300f 4WD tractor. I am looking at installing a front end loader, and a wood splitter, however there are no hydraulic ports. I hear...

I have a Bolens Iseki G154 with a two cylinder engine. it currently has a horizontal exhaust and i would like to put a vertical pipe. does this engine need a muffler to supply adequate back pressure or could i go with a straight pipe. any input is appreciated. thanks.

i have bolens g 154 (iseki tx1300f) and i am in need of a hydraulic pump that mounts on the engine. mine froze and cracked so if this is somthing you have or know where to get one please let me know i have contacted a few places for new prices ranging from $300-$700. maybe some one has a used...

I am looking for a front drive axle (4X4) for this model tractor. Anyone happen to have a parts tractor for sale or know of one? Thanks in advance for any help.