branson 4220

The head gasket has failed on my Branson 4220. There are just 650 hours on the tractor, so I'm a little disappointed, but now I must deal with it. I noticed that the tractor was running hotter than normal, but it never overheated. Then I noticed that there was white smoke from the exhaust even...

Attached is a photo of the timing gear box for the fuel injection pump on my Branson 4220 tractor. As you can see, there's an orange filler cap marked "oil". I looked through the owner's manual and the engine manual, but I see no reference to this oil fill hole. I stuck a finger down the hole...

Need to replace the clutch on my tractor and looking for shop manual. Seems likke everything I find is for the newer models, mine is 2004

We inherited a 4220, the tachometer, hourmeter, and temperature gauge on the instrument cluster have stopped working. I have replaced the alternator (it had gone bad). I have replaced the instrument cluster unit. I have checked all the fuses, and the fusible links, I've checked and verified the...

My Branson 4220 has just developed a problem, or at least I just noticed it. The gearbox grinds hard when I try to shift the PTO into the 1000 rpm position, hard enough that I cannot get it to engage. It shifts normally into the 540 rpm position, though. When I shut the engine off the shifter...

I just wanted to pass on some info I hope might be helpful to someone with any of the tractors listed in the title. I own a 2005 Zetor C42L tractor, which is the exact same tractor (just re-badged) as a Century C42 or a Branson 4220. Zetor started selling the tractors after making a deal with...

I busted the radiator on my Branson 4220 (poked a big hole in it clearing land). The dealer parts cost was $600 which seems extremely high. Checking to see if anyone has used a crossover replacement for the 4220. Any suggestions would be a great help.

Does anyone have a cheaper source for Branson 4220 piston rings other than the 土ourequipmentparts people? Don稚 get me wrong they have everything but the pricing is crazy high!!!!! 1 set of rings is like 80 bucks According to everything I have read I have a Cummins A2000 motor Any info would be...

I have a Zetor C42L tractor with the Kukje (South Korean) A20000N2 four cylinder diesel engine. It is the exact same tractor as a Branson 4220 or a Century C42, just rebranded. All parts are interchangeable on all three tractors, but Zetor discontinued the line about five minutes after...

My 4220 just started giving me this problem and I have not been able to trace it out yet. There are times when I turn the key and I get nothing on the dash, no lights, cannot hear the fuel pump, anything, yet in the past if I let it sit a little while then it would start like normal. Well this...

Last year replace the left side and last week I broke the right side trying to move a large stone.... dumb move... anyway.. I ordered the new kit that fixes both sides. I made the mistake of trying to remove the shroud to get better access to the joint and that resulted in a very damaged...

Anyone know of an online source for parts? The dealer is a ways from me and charges a little too much for shipping/handling. One thing I need is a boot for the loader hydraulics. I also might need an ignition switch.

I was using my Branson 4220 in the woods last week, and ran over a root ball. The ball rotated and the stump (only a couple inches across!) rotated up and hit my hydraulic oil filter. The result was a broken filter housing and a ruptured filter. I'd guess five gallons of oil poured out, and of...

I would like to buy or download a service manual for my Branson 4220. Can anyone tell me where to get a manual and what the cost would be?

My Branson 4220 popped a hydraulic leak in hose from pump to bucket control, replaced the hose refilled hydraulic fliud to the amount of 7.5 gals, site glass verified proper level, issue prior to the leak all hydraulics worked fine. Since if I have the bushog raised and operate the front bucket...

I replaced the air filters and fuel filter because the tractor had low power and would surge occasionally. it ran at low rpm then died. it wont start up now. she will crank but not fire

hi my name is randy i have a branson 4220 tractor with glow plug probs

I have found 3 bad glow plugs was wandering does anyone have the NGK part number for a replacement or any other part number that I can use to buy them locally at NAPA etc.

I've never worked on hydraulics and one of my hoses is leaking. It appears to be coming out of the middle of the hose, a slow seepage. I can get a new hose made, but I need to take this one off and check the fluid. I don't see a note anywhere in the owners manual on how to check the fluid...

Has anyone found a replacement tie rod end that will work with the 4220 just broke yesterday wandering if there is one from local NAPA that will work. Not sure if mine has the upgraded tie rod ends or not it is a 2004 model.

I own a Branson 4220 with the BL20A loader. I'd like to add top and tilt, and I'm finding lots of general information, but not much specific. I guess what I REALLY need to know is whether the control for the FEL will allow for "power beyond". Can I just tap off that control and run a new...

got a Branson 4220 with loader only getting 1200psi at the loader any ideas

I'm about to more than likely acquire this tractor through a trade. I've done lots of reading on here but have not found out what spec hydraulic oil is recommended. I'm not sure right now if I will have a manual or not. Person I'm doing the trade with is trying to get a manual and a second key...

Anyone know where a fellow can buy a service manual for a Branson 4220? My tractor is about two years old now, one more year on the warranty, so I reckon I'll need the manual pretty soon. I've asked at the dealership where I bought the tractor, but so far have had no luck. The tractor's...

Well I finally pulled the trigger and purchased a new 4220 with a FEL, forks and a scraper blade. I had been deliberating for a long time as to whether or not I should make such a purchase as I don't make my living with it. I finally convinced myself to bite the bullet by creatively comparing...

Just Got a new 4220i (kukje 42 hp) 4 cyl.) 17 hours now. Starts fine runs good, however between 1300 and 2100 rpm the engine sounds like it has a loose bolt rattling around in the engine. Some might call it clatter, but it only randomly happens like a tick/ping/misfire every 3 to 5 seconds. It's...

Keep your eyes open for a 2005 Branson 4220 (less than 150hours) with a loader and kodiak 5' brushhog. It was stolen from Orange Park, Florida on 11-28-06 with a 10,000lb triple crown trailer. The tractor has a unique handmade aluminum canopy that is sloped down over the operator station like...

My Branson 4220 i is about six months old. The first couple of months the fuel pumped clicked steadily when I switched on the ignition switch, and waited for the glow plug light to go out before starting. Then it quit doiung that after a couple of months, but the glow plug light came on and it...

Does anyone know what level of oil is suppose to be on my dipstick? My dipstick has 6 marks on it and no indication what they are. I just performed an oil change and put in approximately 6 quarts of oil as that is what I was told it holds and I am between the second and third mark on the lower...

Just wandering if dealers stock these as I never tightened them and noticed 2 are missing 1 on each side on rear wheels where inner rim attaches to outer rim, bolts are gold in color.. so far 45hours on tractor and its running like a top.. starts on 1st. try every time, still smokes on start up...

Noticed over the last couple of days that it has a very good turning radius which kind of surprised me with the 4wd and all...my 03 Ford Crew/Cab dually 4x4 needs a city block to turn around in. Also I need to mount a small toolbox and another waterproof plastic box next to seat or somewhere...

Never used one before.. removed my backhoe and want to mount leinbach auger.. any close up pictures on this site showing what linkage to use, etc.. dont have a book on auger.. Thanks for any help

Will be picking up next Monday or Tuesday as I am going back to Georgia this Saturday.. getting post hoe - tooth bar- boxblade- maybe a rotary mower... from Eton Tractors..Ben the owner is one nice fellow.. saved me 1000's over a comparable Century.. and did not ask for a penny deposit.. I hope...

I had a deal on a new 2004 8404 cadet with woods loader & r4 tires for $15,600.. dealer already sold it but said he could get me another one.. Today I called a dealer for Branson and was quoted the same price for a 2005 4220 with b20 loader and ag tires.. Both have shuttle shift 8/8 on Cub and...

Hi, folks. Please forgive the newbie questions. I have been lurking for a while on the various forums while shopping for a tractor. I liked the Century, but the nearest dealer is about 140 miles away. I understand that Branson and Century are essentially the same, so I found a Branson dealer...