case-ih 254

Today i am changing the gear oil in my IH 254. Following the directions, I removed the (3)drain plugs (diff and (1)ea side), (2)oil level plugs (1 ea side) and (2)fill plugs (top of axle) and drained all the oil. I reinstalled (3) drain plugs and was adding new oil thinking I would add oil until...

IH254 with 1160 hours. I am looking to change the front axle oil. Manual calls for 85W-140, but doesn't say how much. Does anyone know how much is needed to fill? My best guess is maybe 1.5 gallons. Just a visual guess...... I just want to make one trip to parts store. Thanks.

Looking for a radiator cap for an IH 254 (mid 80's). I see them priced online at $100 + . Is there something special about these caps that make them so pricey? Does anyone know of an aftermarket manufacturer priced a little more reasonable? Thanks!

Newbie here. I am looking for a rear replacement rim for my IH 254. All the rims I see online have 4 "loops" to attach. The rusted rim that I am replacing has 4 "z" clips to attach. Is there a way to get the loop type rim to work or do I need to buy a rim, remove the loops and weld on the z...

Hello, I've newly acquired a 1984 IH 254 gear drive. I noticed that some fluid was leaking out of a hole in the transmission just under where the PTO engagement lever is. Was wondering if anyone has one of the similar models and would be able to provide some insight. I've checked the service...

Hi folks, I'm new to all of this. I have a small ranch and the IH 254 with FEL.

I have a IH 254 compact. I am replacing glow plugs. I have replaced glow plug indicator/resistor before and has gone out again. Due to cost, is this really necessary? If so, does anyone know the resistance of the coil. If so, Im sure I can find aftermarket for much cheaper.

Hello. I am a new member and this is my first post. I recently purchased an International 254. The seller listed it on craigslist as a 1985 Case IH 254 diesel with 4WD. Its data plate says it was made in Japan. Anyways it has worked great for me in the past month. But a few days...

Need an external (electronic) regulator for my IH 254. Alternator is Mitsu AH2035H. Tried a VR166 with no luck. Alternative would be a replacement alternator with internal regulator.

Hi, I'm new to the forum and need help. :Last year the 1984 IH 254 I have blew the Hyd pump line that is soldered to the pump. I had that repaired but the shop didn't add any fluid. My helper overfilled the tractor and the line has a half inch split in another area. I'm not finding anyone who...

I am wondering the same thing as jenkinsph as I am looking to move up to a little larger tractor with a loader etc. The tractor is in great shape mechanically and cosmetically. It has the 3 cyl. K3E diesel with 860 hours on it, good rubber (turf), power steering, 2wd and has the ROPS. I do have...

I have a 1985 IH254 with 857 hours that runs great when snow plowing etc. until I mow. I am mowing with a 5' MF 2220 Estate Groomer. After about 20 minutes of mowing the overheat light comes on. I stop mowing and let it run at about 1200 rpm and after about 10 minutes the light goes off and I...

does anybody know if i can put dual wheels on a international 254? if so how thanks

Glow signal is not working. Used to glow on instrument panel . Tractor starts ,but it takes time. thanks sanz

Hello. I just picked up an IH 254 compact tractor. My question is on the PTO. According to TractorData.com, this model should have a live PTO. However, in practice, the PTO disengages when the clutch pedal is pressed all the way down. I had read that some machines used a dual clutch set-up...

turn start key engine will start, climbs to high rpm & dies. feeling the manifold only 1 of the 3 cylinders is warm. combustion problem? please help!!!!

The starter spins but doesn't engage the flywheel. I've never dealt with this problem before. What can I do to fix this? I have some mechanical skills but am no mechanic. Any suggestions welcome. shredder

I have an INternatinal 254 tractor, 3 point hitch that over heats, we flushed the rad, changed the thermostat, put in a new heat gauge and bypassed the bulp to make sure it was overheating, new fluids, no leaks, rad in great condition, air breather new, suction on intake great,any ideas anyone.

My 254 has gotten to where it will not pull itself at times especially when it's under a load. Sometimes I can play with the lift and it will go. I was told there may be a hydraulic clutch assist pack in the trans. Has anyone had this problem or know what the remedy may be? I have the shop...

This is the first time I am posting in the International forum. I have a question about the IH 254, I have done some research and found out that the Mitsubishi MTE 2000D is the same model. What i would like to know is if the IH 254 was a good tractor. The one I am looking at has over 1,000...

I'm new to tractors. I've had this one several yrs but am not very familiar with working on it. The 3ph hydraulics on my compact 254 suddenly stopped working. The 3ph is the only hydraulics on the tractor; no add-ons. It's pretty much just a shredding machine. A couple of weeks ago I...

I need to find a source for hood decals or a full kit for an International Harvester 254 compact diesel. (NOT the Case -IH decals,but the true IH style) These have the red stripe at the top much like some of the 1066 etc decals. Any help please?? Thanks <font color="blue"> </font>

When my tractor sits up a few months the lever for lifting and dropping the PTO sticks. almost to the point of not being able to move it at all. anyone have any ideas on how to loosen the thing up? I sqirted oil around the actual lever but that doesnt seem to help much. tks

23 HP 3 cyl diesel Hard working little tractor