case vac

Need a starter for a vac case anyone know where I can get a brand new aftermarket for it

I have an eagle hitch which has a casting leak so I bypassed the hydraulics to and from the hitch back into the torque tube is that hydraulic system vented any place

So I figured y'all might enjoy a post about my new to me 1952 Case VAC project. So about 2 months ago i Found a Case tractor for sale on Facebook for $750 dollar's. The tractor looked decent in the pic. I called him up and asked for more info He said "We used it last year but, it needs a good...

What fluid goes in Case VAC transmission. Does It share common sump with the hydraulic lift. Anyone ever changed rear main seal on the case gas engine. Thank Rotten Ground

My CASE VAC 1952 turns over but no apparent arc at the plugs, when plug is held in proximity to the head. I have good electricity to the positive post on the coil. Test light goes on from positive post to negative post on the coil. How do I test for current from coil to distributor? and good...

i need a wiring diagram for a 6v to 12v conversion on a case vac can anyone please help me out thanks.

Hi, While working with my VAC 14, I noticed that it wasn't working properly. I then decided to check the oil and found some antifreeze and also it sounded like the motor was only running on 3 cylinders instead of 4 but it never had smoke coming out of exhaust. As I started to drain the oil, I...

I just bought a 1951 case vac and the 3pt worked, then quit. I drained the system, replaced the filter & fluid. The 3pt lifts great now, but my problem is when i drive it, the fluid starts coming out of the breather. Any suggestions? I'm not too mechanically inclined, but not stupid either.

I've got a 1952 Case VAC-13 that I want to restore for brush hogging and the occassional wagon pull (firewood, hay, kids). It had a front end loader and hydraulics, but I don't need them now. Loader is gone. The tractor leaks terribly through gaskets, and I think it is because I have the...

After about an hour of bush hogging today with my old Case VAC,the motor started to miss a little,lost a bit of power. Drove back to barn and cut the motor off and observed fuel streaming out of the marvel carb. Cut the fuel off and removed the air filter,restarted with similar rough running...

Going after my fathers 1950 VAC next weekend. Was running great last time it was cranked about 5 years ago. Looking for advice on steps to take before cranking again, where to buy parts, restore advice.

Hi, I'm thinking about buying a '51 Case VAC tricycle style. Anyone know how it will run in the mud? I've got a mud slick field (about 6 inches deep) that needs to be scraped and graded.

I am new to this site have been lurking for a while and finally joined. I have recently aquired an older case vac for plowing my garden. Was wondering if the rear pto output on these older tractors fit newer implements such as a 4ft bushhog. If shafts are different would anybody know what...

How do we get the hydralics to stop leaking out the breather hole?

I know the firing order of my 1950 Case VAC is 1-3-4-2. What I need to know is which plug is number 1. Is #1 the one toward the dash or the one toward the radiator?

I have replaced the drive gear pin 3 times it will run for a while then it breaks what might cause this problem

Hello friends.. I found an old vac-14 in the weeds and restored it to like new condition...Looks good runs good ...Last month I found another vac and it is in very very bad shape and would like to tractor pull it as my other one only has a 128ci motor and I can't keep up with the 142ci to 188ci...

HI was looking at a case vac for $500 on craigslist it says it runs ok and needs a water pump where can you get a water pump? are these good tractors are they around the size of a ford n series can they run a small bushhog maybe a small baler Thanks

I'm looking for the High Pressure Lift Pump or all the internal parts for it. Checked a lot of sites so far with no luck .

I bought '50 VAC yesterday, runs very well, but it is in much need of a new or replacement exhaust manifold as its present one has 5 nickel size holes. Anyone know where one can be found ? Thanks ahead of time.

Any one here know anything about the old Case VAC? 3ph, live pto, live hydro? How much power? Wide,or narrow front? Any thing else? I see a lot of these for sale REAL cheep. Will they brush hog? Thanks.