ford 4100

Hi all (1st post) Wondered if anyone could advise. I’m in the process of adding a single (DA) lever valve to my 1977 Ford 4100 via the hv5902 adapter plate. My dealer recommended this Galtech Q25 valve and carry over plug. Question is how to plumb it. All valve ports are 3/8” except T1 which is...

I'm redoing all the plumbing on my tractor and loader. The hoses are old and cracked, and I also want to change up the loader valve and rear remotes. This is my tractor, late 70's Ford 4100. It has the internal hydraulic pump. Some tractors have an engine mounted pump or earlier Ford's had a...

Hi- I need help finding the governor spring code for my cav pump It has dpa numbber; 3233F641 cheers Svenn

I bought an 80's Ford 4100 diesel a couple of years ago and I need to change the transmission fluid. However the plug is stripped, so I can't get it out. It's the type with an inverted 1/2 inch square which was almost completely rounded. I couldn't get any bite with my 1/2 breaker bar so I...

The old 4100 that I spent a lot of time on a year or so ago (rebuild thread here https://www.tractorbynet.com/forums/parts-repairs/386813-general-freshen-up-1967-ford.html ) has sprung a leak, it has dropped about 10 litres of oil over the past 6 weeks whilst sitting unused. I have had so much...

Hello, I'm at the point of buying a Ford 4100 (similar to 3000 & 4000 series), but there is one thing which refrains me: the three point hitch doesn't stop. Allow me to explain: If I lower it to the lowest position and let go of the lever, it immediately starts raising again. Even if I do it...

I'm in the market for a slasher and a little-used 6' unit has come up for sale nearby. I'm wondering if this would be too big to comfortably run with my Ford 4100, tractor is rated at 52hp.

Which sockets or wrenches to buy? Might seem like a strange question but I recently purchased a 1981 Ford 4100 and don't have sockets that seem to fit. I was recently trying to take the cap off the rear axle to add hydraulic fluid but didn't have the right size. I have a number of socket and...

As the title says I'm looking for a wiring diagram for the 4100 Ford diesel. I have the I&T manual which has a diagram for the gas but doesn't have the additional details for the diesel. Previous owner did some rewiring and replaced ignition switch with gas version that doesn't have heat...

I just bought a 1981 Ford 4100. I consider myself fairly mechanically handy, but this is my first tractor and have lots of questions. Also I've only had gas autos and equipment and the tractor is a diesel. Overall I feel that the tractor is in decent shape although it has a lot of hours...

As I continue the restoration of my Ford 4100 (see this thread ) I'm starting to look at the loader; the 2-spool valve is shot and I want to add a third function to the loader so I can run a grapple (future build project). I haven't been able to find a hydraulic flow figure for the tractor but...

I'm still wading my way through the refurbishment of my old Ford 4100, all of the hydraulic system inside the casing and the top cover are reassembled. I've come to stripping down the diverter valve to clean it out and renew O-rings etc and found that the housing is cracked at the lugs where it...

We've had this tractor for about 8 or 10 years, it's been very useful for general work around the property like carting firewood, moving dirt and mulch etc but it was in a pretty poor state when we bought it and it has only got worse. The clutch was slipping badly, there was oil leaking out of...

I have recently gone wild and SPLURGED out to buy this dear old tractor.. Its a Ford 4110 and I have used it twice in the last two weeks since buying it , and broken it twice. 1stly I broke one of the chains that hold the slasher steady , and then last week I broke off one of the Glides on the...

Members... I have a ford 4100 with #B962734* and #6A23 above it. What year is it? It's a 3 cylinder diesel with alternator.Also any members have a wiring diagram of this tractor or know where I can find one? Thanks 52 ford.

I went to replace my proofmeter cable but am puzzled by what I found. I pulled out the old broken cable end and it had the part in the photo below attached to it. One end has a square hole and had a short piece sticking out, the other round with the broken cable end in it. I can't figure out...

A friend called me today about his 1977 Ford 4100. The alt. warning light had been on, so he replaced the alternator. No change. I'm going to try to help him figure out the problem. Does any know about this system? Internal or external regulator? I haven't looked at it yet so you know what I...

Anyone know anything about the front hubs on the Ford 4100. Mine seems to have loose bearings, but on studying the service manual, it looks as if the bearings are straight ball bearings, not tapered, and therefore not adjustable. It looks as if I need new bearings (and therefore seals). Have...

I just found a new oil leak, pretty significant one at that. Wierd, it looks like it is coming from the top (left side) towrds the front from the HEAD GASKET. Leak is between the block and head (definately not the valve cover). No oil in water or vice-versa (yet). Could this be something else...

This will be my first tractor and I am looking at a Ford 4100 with a Koyker 200 loader with 6 foot bucket and a 6 foot bush hog, the tractor shows 4700 hours on it and the meter is broken, the bush hog needs some welding, the power steering does not work, the linkage for the differential lock is...