ford 4110

Help, I am trying to identify what I have, the guy I bought it from said it was a 1985 ford 535, but the numbers say something else. The numbers are stamped kd4110 or b, 8e05 d or 8, c782315. I am trying to fix this unit up and I am not sure what manuals or parts to get. Please help! Thanks, Tim

Hello, I have a 1967 Ford 4110 LCG with the gas 201ci engine and it originally was built with the SOS transmission. Somewhere between 1967 and 2005 someone installed a different transmission into it. The new transmission has a HI/LO option and 3 forward gears if you shift up and one reverse gear...

Hello again. I got my 3 point all rebuilt, new o-rings and adjusted to where I think it should be. It lifts great but bleeds down slowly. My actuator handle will not fit right on the lever shaft so I cannot use the handle....yet! As you can see through the pictures I have a remote hydraulic...

I got the tractor hydraulics rebuilt and placed back on the tractor but I cannot get the three point actuating lever to move.

Can someone please tell me the location of the hydraulic drain plug on thi tractor? Also, when I fill the hydraulics, does it fill the rear end also?

Ok, well, I am rebuilding a tractor I bought from an elderly guy who started taking it apart. I am working on the 3 point linkage system and I have used most of the parts in the box except for a few bolts. It looks like in the picture something is supposed to go into this plunger but not sure...

I bought a 4110 tractor 3 cyl Gas and it has a couple of problems but not sure about them. The tractor turns over but doesn't start, no bigee I dropped it off at a mechanic friend garage. There are a couple of parts I am not familiar with but will figure them out, the 3 point lift ram and the...

Hey guys I just purchased a 1968 Ford LCG for $1500 runs and drives pretty good. I think it has the 201 gasser engine question is I live in southern Idaho and weather is extreme from well over 100 to -20 below. I have been running straight 30w in the tractor but when I started it up to plow the...

hi I have a ford 4110 tractor 2 wheel drive with power steering , I bought it to repair as it had a hard life with a loader fitted ie front spindles and bushes worn out ( never seen grease in there life) the power steering Rams where disconnected I have since repaired the font spindles and...

Does anyone have firsthand knowledge in correctly diagnosing the above fault. I bought the tractor with front end loader attached and over time the steering has begun to toe in or toe out particularly on the right wheel. From what I can tell the possible cause is a worn seal in right side power...

Hi there, I have a Ford 4110, 2WD, 3-cyl diesel all purpose tractor manufactured in England in September, 1988. I live in Australia. There is a significant leak at the join between the top housing assembly of the power steering unit (Part No: E4NN3C516AA) and the lower housing assembly of the...

63HP/48PTO HP. Diesel engine, newer gigantic rear turf tires. What's it worth. Don't know year. Seller claims 100% running order. No problems.

Hi there, I have a Ford 4110 Series 2 two wheel drive. The numbers are: KA314D, 8J03 and BB74558. Can you tell me the age of my tractor. Thanks, Ged

I parked the tractor a few weeks ago and it was running fine. Now no go. I have fuel spraying out of the bleeder plug on the IP as far as the tire, but nothing at the injectors. I also have a small trickle of fuel coming in the return line to the tank. Ive cranked and cranked it for what seems...

My father is looking to buy a well used Ford (I'm pretty sure its a Ford and not NH) 4110 (50ish HP) from the local New Holland dealer. The dealer has done some minor drag link repairs and it needs new 3 pt hitch links. The machine has 1800 hrs on the hour meter, and looks to be in fair shape...