ford 951

  1. L

    Ford 951 special brush hog, help. Can't remove drivetrain yoke from gearbox input shaft

    removed shear bolt, yoke wont budge. read that there may be snap ring on shaft, but don't see one. does appear to have notch for key stock, but does not appear to be any key. NO movement, forward, back or round and round. Pretty ancient, was already ancient when I bought it 15 years ago. Any...
  2. L

    Ford 951 Special Mower- what to do?!

    Hey folks here is a pic of my mower the deck is getting beat, and I was planning on replacing it this winter, but some thing have changed. I was using it last week and noticed I couldn't pick it up all the way? The arms where up but not the back wheel? After I unhooked it this is what I...
  3. redneck83

    Rotary Cutter  Ford 951 Special

    Hi, i just come across this rotary mower and was wondering if they are good pieces of equipment? I think its the 5 foot model. I have a 1964 ford 2000 LCG that i will be using it with. Will this tractor be enough to handle it? Any info i can get would be appreciated. I am adding some pictures...
  4. M

    Problem Starting 1960 Ford 951

    Please help, I think I have tried everything. I have 1960 ford 951 powermaster which was running this fall. It was previously converted to a 12v system. When I garaged it I thought i would do a basic tuneup, and noticed the spark plugs were in firing sequence 1-2-3-4 instead of 1-2-4-3 so I...
  5. carroll ertel

    Ford 951 Special rotory cutter shear pin

    I have an old Ford 951 Special rotary cutter . The shear pin has broken off and the pieces are gone , the only thing i can figure out is it must be some kind of bolt with a blank shank with a lock washer and nut to hold it in place . The hole does not appear to be tapered as it would be if it...
  6. M

    Ford 951

    Hi, Need help in locating the center offset bar for my Ford series 951 brush cutter. The numbers are as follows: Series 951, Component # 22BM1475, Serial # 32419. I've tried the local Ford New Holland Dealer with no success. They make two types, one of them is flat and the other is offset...
  7. G

    Flail Mower  ford 951 special problem help!

    I have a ford 951 special (brush hog) I keep breaking the u-joint near the pto when hitting hidden rocks or small stumps and not shearing the bolt at the gear box. I bought this unit used and have no owners manual. The shear bolt is a grade three bolt. Please help Me I'm tired of replacing u-joints.
  8. Soundguy

    ford 951, my next victom

    Update... have been fixing leaks and neating up wireing and replacing broken fasteners.. etc. had to drill out a broken bolt inthe front pedistal, and replace a few small parts.. belts.. etc. found some tinwork on ebay ( machine used to be LPG, but was converted to gas.. thus old tinwork was...
  9. Soundguy

    got a ford 951

    Been absent a few days as i made a run from florida to texas to pick up a ford 951.. am tired and hitting the bed. did a 48hrround trip red eye there and back. soundguy
  10. T

    Ford 951 Mower Cross Reference

    I have a ford 951 mower (5') that I need to get new blades for. Due to the expensive nature of the original factory parts, I am hoping that someone might have knowledge of some less expensive parts that I could use. At one point someone told me that there was a mower that uses alot of the...
  11. B

    Ford 951 brush hog parts

    Anyone know of a place online that I can order parts for a Ford brush hog? I had a brush hog given to me, but I need to repair/replace the gearbox on it. Any help would be appreciated.
Top