hydraulic issue

I have a MF 1533, and I am adding the Messicks 3rd function kit. However my tractor does not have a power beyond port and I have been instructed by messicks to plum it into the return underneath my tractor. The problem is that the kit I have is only rated for 12 gpm and I have heard that the...

I recent purchased this tractor that had been in a field for years. went through and changed all fluids, filters, screen and cleaned out the insides. The front loader is slow and shakes lifting, going down is fine. Same happens when I curl up. Curl down is fine. Plenty of fluid and all new quick...

Hi all, Currently working on an old Eicher 364 and having a difficult time with the hydraulics. They worked briefly and then stopped when I tried to bleed them. Measured pressure at the pump output line is 200 PSI at idle, up to 1000 PSI at max RPM. The manual says it should cap at 2438 PSI...

Removed the front end loader from 1025r. Re-installed 2 hours later. Now, when I try to tilt the bucket down, it comes up. Hoses are connected properly.

I just changed all fluids and filters and afterwards drove the tractor back to the barn all seemed normal. A couple days later I went to hook up the bush hog and noticed that it seemed to lag when I put it in gear and after “sluggish”. The engine was running fine. I drove the 200 yards back to...

My L3400 with 700 hours won't stay in Medium, High and Low work fine but it pops out of Medium I had someone look at the linkage but no adjustments. Has anyone had similar issues?

I have an hydraulic leak at one of the supply line fittings to the loader control on a NH 2120. Assume it is a JIC 37 degree flare fitting. Is it reasonable to think that I can stop this leak without having to replace the entire line (because of the flared tubing end)? Has anyone had...

Hello all, Looking for some help here, snapped the control arm on the left wheel assembly yesterday. I have a 2014 LS 4047R. I was in uneven ground doing some road work and the right wheel hit a large rock in the bank I was pulling material from. The control arm snapped right where the tie rod...

2 Weeks ago I picked up a Yanmar YM1510D. It runs great but the Bush Hog 1846QT loader was not installed because it was leaking. I install the loader and hook it up (how they told me). I have no hydraulic fluid making it to the loader. I add fluid, clean the strainer, unhook lines, and the whole...

I was bushhoging with my grandpas 1973 ford 2000 diesel last summer and the back tires went down in a little ditch and the bushhog stayed up on the hill so I was stuck until I raised bushhog. Well after that the high pressure line going into the hydraulic pump blew out. So we pulled it up to the...

Hi! This is a "Deere" LVA 12456. Trying to find one. Deere wants nearly $800. Does anyone know it there is a way to fix these? TIA Troy

Hi there, Looking for some help or advice on this one. I have a Kubota m8560 with a single set of rear remotes and a Kubota FEL. It's got about 300 hours on it, and I've owned it since new (few years now). I check the hydraulic level on the dipstick near the PTO regularly. For the last 250...

Hey everyone I've been having an issue with the JD quick connect 54" plow on my 2014 JD 2032R (first gen). It operates normally up, down, and left, however when I move the joystick right I cannot move the lever all the way or the plow will go the opposite direction. If I move the lever 60-75% it...

Team, With Summer upon us I'm putting aside time to finally diagnose this device. I put a new engine in it last Fall which seems to run well. The lingering issue is this: The tractor loses power when going uphill. It will bog down and stall the engine if I allow it. If I let off the...

L3130. Replaced blown bucket hose. After repair pump whines and no hydraulic action. Tractor will move but no loader or rear lift. Checked for all hose connections and changed out both rubber suction hoses. It was suggested water got in hyd oil, causing a gel blocking filter. Pulled and checked...

I'm a first time poster and first time tractor owner. I have searched up and down on the internet and this forum and couldn't find others with my same symptoms, and none of the proposed solutions for similar issues have worked for me. My maintenance experience up until now has been servicing...