massey ferguson 1045

Hi folks, I'm getting annoyed by my Ford 1700's lack of 4wd and overall lack of traction and pulling capacity in the mud (and it's muddy here half of the year). I have two tractors that I'm looking at. They both come with a loader and a backhoe: MF 1045 - $6500 Owner says power steering needs...

My front left hub is toast. I am trying to save it but I would rather replace it with a good used 1 if anyone is parting out a machine. Otherwise, I might part out mine.

needing part for massey ferguson 1045. part # 3436943M1 13 tooth gear axle drive shaft. part is no longer sold in part stores.

Does anybody have an idea were I can get a Birfield joint for a 1045 Massey Ferguson?

Looking for a manual... In the interum, anybody know how long to cycle the glow plugs? It's getting colder and begining to need them.....:)

I bought a MF1045 4x4 Loader Tractor. I'm suspect in it's previous life it had a frame mounted backhoe that would normally require removal of the vertical and lower 3 point linkages. Now just a loader tractor with 3 point hitch, the hitch lower link drawbars don't seem to have enough lift. When...

What would the stock FEL be for a MF 1045?

Looking everywhere for a replacement head gasket. Any ideas on where to get one. Checked all MF dealers. Can one be made and by who??

Please can someone tell me what engine this machine has.

Hey guys, Looking for a replacement part for a broken 87AC BIRFIELD NTN-EL5 front CV joint for for my MF1045. I've already contacted Leonard Sheaffer at Sheaffer's Town & Country Tractor but he wasn't overly optimistic.

The low range on my MF 1045 has always been funny. When I bought it used in 2002, it would occasionally pop out of gear. Then, last week while rototilling, it stopped working altogether. Well, it does work, but it jerks the tractor forward an inch, and the makes unpleasant noises. Has anyone...

I've been looking around at several used tractors and have been back in forth on a few models and I'm getting to the point where I need to make a decision. So I am wondering if all of you MF owners might be able to offer some thoughts. I am looking at a '88 MF 1045 with a 232 FEL, FWD, 800...

My 1045 needs a water pump, does anyone know where to buy one or have it rebuilt. I'm afraid to call Agco, as they probably want like 200 bucks for one.

Hello. We've had this MF 1045 since new in 1990 and it has just over 500 hrs on the meter. It has been used primarily for making hay - no loader, no back hoe, no plowing or discing. It has developed a grinding noise in the transmission and it seems to be getting worse. When disengaging the...

Hello all. I recently inherited a Massey Ferguson 1045 with turf tires with a little less than 500 hrs on the meter. My wife's father bought it new around 1990 and used it mainly for cutting/making hay on the old farm. Anyways, I'm not sure whether to keep it or sell it. Someone told me that...

I was told my 1990 MF 1045 crosses over to a Hinomoto, does anyone know what model, would it be easier for me to get parts thru Hino dealer or MF. Anyone on here familiar with this tractor?

My 1045 has a kinda whining noise, sounds like it's coming from under the seat, kinda like when you open a hydraulic cylinder fully and hold the valve there and then it kinda whines, not real loud, but it's there, and I can't explain it any other way. If you push the clutch pedal down it goes...

Looking at a 1045 with loader 2200 hrs 4wd, how much is it worth and is it a good machine?

I am new here, and need some help. Can someone please direct me to anyplace that carries the gears for the rear-end of a 1045. or, sell me a broken down 1045! thanks