My T post puller

   / My T post puller #1  

SSdoxie

Elite Member
Joined
Jun 25, 2010
Messages
2,694
Location
Cumberland Plateau, TN
Tractor
Bobcat CT225
Here is a little gadet that saves some time and effort pulling T posts. Took me about 15 minutes this afternoon making it from some scrap angle iron laying around.
In the photos I was pulling off the Quick Hitch on 3 pt. Just back up close to post, drop the triangle over the post, lower 3 pt, then pull, up comes the post.

The triangle measure 5 1/2" from top joint to the cross angle. This one is 2 1/4" wide at the bottom. I think 1 3/4 or 1 7/8" would work better since this on did slide off to an angle a slipped on 1 psot out of the 8 I pulled, a little narrower will keep it from twisting off center.
 

Attachments

  • T post puller 006.jpg
    T post puller 006.jpg
    91.9 KB · Views: 1,910
  • T post puller 001.jpg
    T post puller 001.jpg
    159.5 KB · Views: 2,258
  • T post puller 002.jpg
    T post puller 002.jpg
    203.8 KB · Views: 1,856
  • T post puller 003.jpg
    T post puller 003.jpg
    174 KB · Views: 2,126
   / My T post puller #2  
Here is a little gadet that saves some time and effort pulling T posts. Took me about 15 minutes this afternoon making it from some scrap angle iron laying around.
In the photos I was pulling off the Quick Hitch on 3 pt. Just back up close to post, drop the triangle over the post, lower 3 pt, then pull, up comes the post.

The triangle measure 5 1/2" from top joint to the cross angle. This one is 2 1/4" wide at the bottom. I think 1 3/4 or 1 7/8" would work better since this on did slide off to an angle a slipped on 1 psot out of the 8 I pulled, a little narrower will keep it from twisting off center.
Good job on the puller. It looks as if it will slide down by gravity for a second bite if needed.
 
   / My T post puller #3  
Looks great. If the t post has no bumps, you can put a bolt through. Handy.
 
   / My T post puller #4  
Thanks, SSdoxie, I will add that one to the list of ideas stolen from someone else.:laughing: Great job!:thumbsup:
 
   / My T post puller #5  
Making one on friday..Thanks. :thumbsup:
 
   / My T post puller #7  
love the simple design; will make one soon
 
   / My T post puller #8  
Thanks for the idea. I made 2 last week. I'm retired & pittle around in my shop most of the time. I like building stuff like this & giving it to people just to watch their reactions. Great little tool thar really works.
Any more ideas?
 
   / My T post puller #9  
I like the puller a lot. Good job.:thumbsup:
 
   / My T post puller #10  
nice Job,

Good little tool to have around and make a job fast and easy.
Or its a chain and a helper to do the same job in the same time.

Nice Job
 

Tractor & Equipment Auctions

2004 Ford F-250 4x4 Crew Cab Mechanic Service Truck (A49461)
2004 Ford F-250...
2012 Ford F-350 Crane Service Truck (A48081)
2012 Ford F-350...
20 Gallon Air Compressor (A50860)
20 Gallon Air...
2017 Isuzu NPR Crew Cab Landscape Dump Truck (A48081)
2017 Isuzu NPR...
2020 Cat 299D3XE Skidloader (RIDE AND DRIVE) (A50774)
2020 Cat 299D3XE...
2013 John Deere 324J Wheel Loader (A50490)
2013 John Deere...
 
Top