Trailer for 4720 TLB

BobQ · May 9, 2009

I am looking for a new trailer for my 4720 TLB, I am wondering what weight and length I need? I want an equipment type that goes on my hitch.

I am thinking a 10,000GVW and not too sure on length? Maybe 16 or 18 foot?

Any help would be appreciated.

Bob

George2615 · May 10, 2009

Tractor Data lists your tractor as 2580 lb plus loader and BH probably puts you in the 4500-5000 lb range. A 10K trailer is more than capable to haul it. I'd suggest an 18-20' trailer. Say 5k for the tractor plus a 2500 lb trailer puts you at 7500 lb. most 1/2T trucks can haul that load. A 3/4T would be better.

Most equipment trailers have pintle type hitch but also can have a 2 5/16" ball hitch. For securement of the tractor on trailer I suggest 4 chains and binders (one each corner) plus a chain or strap for each implement.

Equipment trailers are not as wide (width between the fenders) as a car type trailer so keep that in mind if you ever want to haul a full size vehicle such as a pickup in the future. My trailer is a tilt bed H&H trailer I bought in PA. They, of course are more expensive than non tilt but they also have equipment type trailers. Being in the northeast I found it cheaper to buy in PA. Trailers here are expensive probably because most are not made in the NE and dealers have to add shipping charges. You can also check Ebay or Craigslist for used trailers in your area.

carpenter383 · May 10, 2009

If tractor data has a 4720 at 2580 lbs. that's a misprint. A bare 4720 is around 4000 lbs by itself. I'm not sure how much the loader and backhoe wiegh, but I bet the total package is more like 6500-7000 lbs. So a 10,000 lb trailer should still be ok.

George2615 · May 10, 2009

My mistake. Carpenter is correct. It is listed at 3910 base weight plus loader and BH. I was looking at 3 pt. lift. Even at 3910 plus about 2200-2500 for BH and loader the 10K trailer will be what is needed.

BobQ · May 10, 2009

Great, I am on the right track. I would like to get a 18 foot just so as to be a little easier to move it around my property, I am looking at a Bri-mar. Funny, I can never find anything used? or it is in bad shape and a lot of money? I have a Dodge diesel 3/4 ton for pulling with brakes, in the past I would rent or borrow a trailer when needed, neither are available any longer.

Thanks Bob

jgreen · May 11, 2009

Hi Folks,

I thought I would throw my 2 cents worth in the conversation. I have a 2810 with FEL and hauled it on an 18 foot trailer which worked fine with just the tractor and FEL. When I wanted to haul it with my 6 foot brush cutter I quickly ran out of length on the trailer. I also agree with george2615 don't forget the trailer axles must carry the weight of the tractor and equipment but also the weight of the trailer should be figured in what the axles and tires of the trailer must carry. Don't forget to also figure any ballast you may have added to the tractor for total weight.

Happy trailering!

JG

jhkfarms · May 12, 2009

Just for some information, most of these trailers are assembled there at the dealer. If you can afford it, have a steel floor put on the trailer, if not see if they will use pressure treated wood. Watch the tires they try to put on them, you need 10-12 ply. Last is if you can afford it, get a hydraulic tilt trailer, it will save you the constant use of the loading ramps. I don't know how much you are wanting to spend, but the tires and floor will save you a lot of money and headache in the long run. I learned the hard way, with a load of hay on my trailer and blowing out a radial tire. Now I have to replace my floor, do to boards rotting.
JHK Farms
4720i