Recent content by BAGTIC

I am looking for a quick attach converter for an old Ford 2000 with a Ford series 703 front end loader. I do not weld and don't know anyone nearby to do it for me. Does anyone know of a QA plate that would 'drop in' to existing pin holes without requiring cutting/welding?

I am looking for plans for making a PT425 quick attach plate. I seem to remember one here some years ago but I just can't find it and "Search" did not help much.

I have a 425 with a 48 inch finish mower. The treads in one of the spindles have stripped. I would like to get a new spindle unit but don't know what brand spindle Power Trac uses. I doubt that it is their own design. Does anyone else know? Also where can I get some of the little blade...

I am looking for an extra set of 12 inch wheels for my PT 425. The old wheels are 12 x 8.50 and I am using the Carlisle 23 x 10.50 x 12 'Super Lug" 4 ply tires. I want a sets of six ply or better because I get too many flats from branches, etc. in the brush and woods. The wheels on the John...

Are the quick attach plates on the PT425 and the PT1430 the same size? I have a 425 and would like a really big light material bucket for handling wood chips. The 425 LMT heaped full doesn't come anywhere near the 425's lift capacity.

The 48" rotor tiller for my PT425 has blown the hydraulic motor seal. I took it to the local tractor repair shop but they said they need to know the motor manufacturer/model number so they can order a kit or new seal and bearing. Does anyone know what motor is on the tiller. I bought it in...

I have not been on here for a long time but I need some suggestions. What engine would be a suitable replacement for my piece of Robin crap? Any opinions on the Kohlers amd B&S models? Do most small twin engines in this size range have common base mounting dimensions or would it be necessary...

I personally see lots of little flaws in my PT-425. I would like to make some suggestions to PT for improvements. They are free to use any of my ideas. 1. My pintle hitch cracked loose recently. The top weld to part of the rear grillwork broke the grill are tore out at the corner. I do not haul...

Does anyone make an HST tractor with at least 50 PTO h.p. and AT LEAST least 17 g.p.m. auxiliary hydraulic systems? I don't need a tractor for plowing or heavy pulling. I need a 'tool carrier' to operate different attachments

What is the slowest speed in a Kubota M9000. I am still looking for the right tractor and the M9000 looks attractive but one thing it must do is travel very slowly as I want to use a chain trencher on it. The trencher manufacturer recommendations are: "You would need at least 17gpm to operate...

I have 82 acres slightly hilly land but nowhere I can't go in a 1970 GMC 3/4 ton with auto transmission if I am patient. 75 acres are pasture the rest buildings, ponds, landscaping and a small 1.5 acre orchard. I need a tractor primarily for pasture maintenance (brushhogging, seeding...

The PT on steroids? New Holland Bidirectional Tractors

I have alrady worn out my 14" auger bit, at least the teeth and the point, in about 75 hours of use. I started searching the internet for some replacement carbide teeth and points that would be more durable. It was then that I noticed that the PT augers seem to be a non-standard dimension. They...

Does anyone know of a brush mower than can be front mounted via QA? Of, course it would need to be hydraulic powered. Because of cervical arthritis I have problems with rear attached implements as I had difficulty observing them except via rear view mirror.

Does anyone have an over 50 hp tractor with a CVT transmission? What is your experience with the CVT transmission? The smallest farm tractors I have seen advertised with CVT are 100 hp which is a little too big for me. I would probably be looking at something in the 50-70 hp class. Does anyone...