Search results

I am trying to adjust the anvil on the Jinma chipper, but I don't think my approach is good. I'm using a piece of sheetmetal with a single bend, going down it's length, as a shim. The blades are not vertical with the bottom of the blade being roughly .100" closer to the anvil than the top. I...

I'm using my 2' wide bucket on the backhoe to dig a 3' wide trench (in two passes). The first pass goes fine, but when I try to take a second pass cutting a 1 foot wide swath, the bucket tends to veer off to the side, and pulls the tractor (Kubota L5030) out of position. The stabilizer pads...

I have seen suggested gap between the knife and anvil between .015"-.035". I replaced one of the blades, and was looking at the gap I currently have between the blade and anvil. It's just above 1/4". I haven't tried to adjust the anvil, but I'm guessing there isn't enough adjustment to bring...

I need to service my Jinma and looking for replacement blades and anvil - Anyone know if they are still available, and if so, where? If they aren't available, what have others done to solve the problem - e.g., modified some other parts to fit, or fabricated from scratch. Thanks

Does anyone have an opinion on which is better? If so, what are the differences that make one better?

Anyone have any experience with Mighty Max pallet forks? I don't know anything about the following company, but they carry the forks. Any feedback on the company would also be appreciated (budgetforklift.com) Skid Steer Pallet Forks - the Mighty Max

I hit a roadblock with the Jinma chipper - the pto shaft isn't long enough (10 - 12 inches) - I'm connecting it to a L5030 Kubota which can accommodate Cat 1 or Cat 2 hookups. I'm not sure what my options are - I know I can buy a different PTO shaft, but wondered if there were other options...

I plan to connect a Jinma 6" chipper to a Kubota L5030 in the next week or so. The flywheel appears to be substantial, and most likely will continue to turn even though the PTO has stopped - Anyone know if there is any danger of damaging the tractor if the PTO being directly connected to the...

I am going to be running a Jinma 6" chipper on a Kubota L5030. The flywheel appears to be substantial - Anyone know if there is a problem with the PTO being directly connected to the chipper. My concern is when the PTO is stopped and the flywheel of the chipper continues to spin. Do I need to...

I'm looking at both Leinbach L7200 and L7300 diggers with 6"/9"/12" augers for $600 and $650 respectively (plus shipping). Anyone have any knowledge of Leinbech quality/durability? Is this a reasonable price for Leinbach? The diggers will be used in fairly high clay content soil with some...

I have a hydraulic leak at the quick disconnect between the backhoe and the tractor. It was present on the supply side of the backhoe prior to uninstalling the backhoe (mounted 3 pt disc). After reinstalling the backhoe the return side coupler leaks. I assumed it was dirt particles, but did...

I just purchased a 2003 L5030 with BH90 backhoe. I disconnected the backhoe and connected the male and female hydraulic lines together (the ones that went to the backhoe). I'm now trying to figure out why the 3 point cylinders don't respond when raising/lowering the control lever. I have...

I have a Kubota BH90 backhoe with mounting brackets which look to be in the way to connect the 3 Pt stabalizer assembly. Has anyone worked out a way where they can have the 3 point linkages/stabilizers in place without taking off the backhoe brackets?

I just received a 2003 L5030 with FEL and BH90 Backhoe. It doesn't have hydraulic cylinder nor lift arms/linkages. I'm looking for the best way to add to the tractor - is the draft control worth adding? How much should I expect to pay to add this? Is Kubota the best source for the parts, or...

I just purchased a 2003 Kuboa L5030 which came with turf tires - I will be pulling a disc with it and suspect the turf tires will have some problem gripping and am looking to see if there is a used set for sale. Anyone know of a good site to be watching?