Search results

I need to replace or rebuilt a final drive, looks like they are all made in China. Anyone had a good experiance with a company? Thanks Vern

Morning I am getting air in the water lines, I have taken out the "tire tube" valve an made sure it was clean but I am still getting a lot of air. Any help is appreciated. Vern

I lost 4 wheel today, didn't hear anything, but no power to the front wheels. what to check? Thanks

Hi Thought I would share this. Home made backhoe that I totally abuse. Amazed it can dig these pine stumps out.

The Shrader valve is below the pressure switch.

Was out by the well house and could hear the pressure switch kicking in and out (loud click). Opened it up and found black fibers and soot on the cover. Turned on the water and the switch was kicking the pump on and off 45 high and 30 low, this is constant while the water is running. the water...

Yesterday the shift lever starting getting really hard to shift between gears. I took the tans top cover off and can feel the binding in the arm that goes into the top cover. Has anyone experienced anything similar? Any pointers on what to look for? Thanks Vern

The entrance to the camp has been a lumber dock and we could drive right off the gravel into the property. VDOT got the bright idea to dig a 12" wide by 6" deep ditch right across the gates, state maintained gravel road. I put in a private entrance drive permit and was told I would need to...

Hi I pulled the bucket off my FEL, the bucket mounting holes are wallowed out so need to make some peices to fix it. Has anyone found a supplier for the wear bushings on the loader arm? Its a Yanmar 1575, Hoye does not carry them. Thanks

Morning Bucket on my FEL dropps, sometime fast some times slow. Put new o-rings in the control valve - nothing changed. I pulled the pins for they cylinders off the bucket and the left one creeps out, the right holds position. Question - Can one bad cylinder cause the bucket to drop? Thanks Vern

Good evening Finally finished painting and going through my RZ60 Bush hog and hooked it up to the 336D. Bush hog ran great, have to do some 3-point adjustment but satisfied with it. I do have some questions on the PTO- should it not stay powered when the clutch is pressed in? I think what I am...

Got these off my trail cam next to a mineral lick.

Good evening Loader started dropping the bucket today. Bucket will just start dropping and very quickly. Looking for some where to start looking for the problem. Have a joy stick control. Was wondering if it could be the quick disconnet leaking by, I had an o-ring come out of the ball on one...

Does anyone know if the hood off a YM2000 will fit my 336D? There is one on ebay. Thanks

Good morning While working at the camp Sunday morning I broke the streering arm to the right side front wheel on my 336D. The threads holding the rod to the ball joint stripped off inside the rod. To many stumps!! Used the bucket to raise the front end and got it back in the hole and then used...

Took a couple of days off and have been clearing the mess left behind by the thinning company. I cannot believe the amount of stuff!! The tractor has worked like a champ. I built some brush forks for it an they are the ticket. Too much for the 336D though so will look at renting a bulldozer. to...

Yanmar YM180

Got this off the cam on my property in Southampton County VA

Hoye lists two front dfferentials - old style and new style depending on the serial - where do I find the serial number? Mine moves back and forth when turning the steering wheel so figure the bearings are shot. Thank you

Evening I have had such great help from this site I figured I would try here. I answered an ad on Craigslist for a 96 Yamaha Big Bear 350 with a bad rear end. The guy wanted 450.00 and it looked like a do able repair. When I got there he also had an 02 Polaris 700 sportsman - a beast, that had...

Good morning I closed on 24 acres in Southampton County VA on Friday. The pines had been thinned earlier in the year but they left one heck of a mess. The trailes are piled with cuttings and needles and they left stumps up a couple inches. To be able to plant a small food plot this spring I...

Evening ordered new injectors from Hoye today, forgot to find out what the torgue spec's for the flange bolts should be. Anyone know? Thanks Vern

Hello I bouth a bigger tractor- Yanmar 336D- so I am going to sell the 550 Satoh with the Woods finish mower. Tractor is in reasonable condition - original paint with some rust blleding through. Starts good, cold blooded but once warmed up runs good. Uses a quart of oil per season but puts a...

Hello Bought a 336D last night and having it delivered this afternoon. 1300 hours with FEL, post hole digger, finish mower, and rack. There has been some damage to the hood, the hydralic hoses are leaking at the quick disconects, and the front tires are worn. Runs good and everything works...