coldsteelva
Veteran Member
Any response to Post #5?
No... I'll have to address it once i finish the build, paint, and mounting. I also need to drop the truck off at my sandblast guy so he can clean up the frame. I want to repaint the truck frame and mounts while it's all exposed. Also going to swap in new rear shocks and service the rear axle while I've got room.Any response to Post #5?
Ongoing project... I'll post updates as it goes. I'm hoping to complete the project within the next couple weeks. This is going on my 05 F350 ShortBed. The flatbed will measure 94"x80". The deck material will be wood.
Took the bed, bumper, tailgate, lights... off the truck and sold them on Craigslist.
View attachment 501044
View attachment 501047
Picked up my steel order from my local steel shop. I have about $750 in steel (which includes the custom cuts). I'm using heavy gauge structural C-channel for the framing. 1/4 " plate for the side rails. 3/16 " plate for the rear "apron". I'll be building the bulkhead/headache rack out of 3/16" walled 2"x3" box tubing.
View attachment 501048
I'll be retaining the factory rear trailer hitch, but building in recessed 5th wheel rails with a gooseneck adapter plate (for towing flexibility).
Spacer blocks for the frame rails:
View attachment 501049
Each frame rail will be mounted to the truck frame with (5) 5/8" grade 8 bolts, bolted thru the original mounting holes on the top side of the truck frame. There will be an additional (not pictured) 5/8" bolt on the outer side of each frame rail, bolted thru a C-channel bracket.
View attachment 501050
View attachment 501051
So in total, this flat bed frame will be mounted to the truck with (12) 5/8" grade 8 bolts.
...........
Now that the mounting points are drilled and completed, today i can start welding the cross-channel pieces.
More to come...
A couple points: If your 2005 only came with red tail lights (tail/stop/turn/hazard), how are you going to make it so your taillight reds don't flash with the turn signal? Can't cut the wire to the high filament because then you would have no brake lights. Making the amber signals work is easy if you run them off the front turn signal circuit, but you will still have the issue of the reds being brake lights, but not a turn signal.
The reds I'm buying have dual intensity built in, actually a "halo" ring for the running lights... Along with 3 wire input (ground, running, turn, brake, your choice)I've solved this before on a couple chevy trucks by using dual LED's - and leave the inner lights brake lights, and the outer lights turn signal. So they don't all operate the same. If that is unappealing, you could tap into the trailer wiring to get dual functionality out of one led.
The reds I'm buying have dual intensity built in, actually a "halo" ring for the running lights... Along with 3 wire input (ground, running, turn, brake, your choice)
If you read the description of the lights he was looking at here 4" Inch Piranha 1 LED Round Stop/Turn/Tail Truck Light 2 Red 2 Amber 2 White | eBay It says those red leds also have 3 wires, so he should be good, just put the amber lights up front on the sides of the new bed.
One warning; Sometimes LED's don't work well with the OEM flashers. By 2005 you may not have a problem, especially if you leave the front bulbs regular incandescent bulbs. But if you start having problems with the lighting, suspect the LED's not being compatible with the trucks's flasher. You can get load resistors if you need them to fix the problem.
One warning; Sometimes LED's don't work well with the OEM flashers. By 2005 you may not have a problem, especially if you leave the front bulbs regular incandescent bulbs. But if you start having problems with the lighting, suspect the LED's not being compatible with the trucks's flasher. You can get load resistors if you need them to fix the problem.
I'll be retaining the factory rear trailer hitch, but building in recessed 5th wheel rails with a gooseneck adapter plate (for towing flexibility).
The fifth wheel rails are welded to the main flatbed framing beams, which will be bolted to the truck frame with twelve 5/8" grade-8 bolts.Will this be attached to the frame or body only? You have some nice "iron" in your sig. pic and guess you move it with a g/n. (that should be frame mounted).