Hello folks, I have a JD 14t baler that has been working fine over the years. I got it out this year and with the old twine it would bale and tie but the right side would break right after the...

If the PDF doesn't work for you, go to the address below for the same manual online which also contains the manual for he version with the motor mounted on the hitch. John Deere 14T Baler Manual

Hi- I just joined the group and am trying to send a general call for help to anyone who might know how to install a knotter on a JD 14t baler. I bought this 14t baler 2 years ago and have baled...

Have a new to me jd 14t Baler. The oil seal where the plunger crank shaft enters the transmission (for lack of a better word) is leaking. I posted earlier today looking for advice but for some...

Hi, I have a 14T baler, with manual, and have some issues with one of the knots. The left one (if you are on the tractor) is quite often loose. When I use the modern plastic twine, 1 out of 3...

My neighbor down the road is looking to bale about a 200 bales from a small field using a 14T and his JD 1025R 25 HP small tractor. All flat land and dropped in field. I told him I had my doubts...

Looking for some help! The needles on my 14T broke the other day and was able to find a set from a tractor graveyard about an hour away from me. They were off of a 14T as well, and look great...

Hello all. I bought a JD 14T baler and have been getting acquainted with it slowly. The guy i bought it from got it from a neighbor who said it had been shredded for over 20 years. I figured...

Good morning..... This is my 14T baler.... I've had it for about 4 years and tweaking on it to keep it working very well..... Replacing parts as needed.... The knotters are last on my list due...

I am looking at a JD 14T baler. It is in good shape and is baling but the left knotter frame is cracked. Is this knotter frame interchangeable with any others from JD?

Got the baler out and figured that we would go without a problem and it won't tie a knot, the needles even lose the baling twine some how...we have just been running it through the cycle by hand...

I have a few questions on this baler. Hope someone can shed some light on this.. IN the pic. The pink circle is loose.. Questions is why? The blue circle has bolt missing? The red circle.. Are...

which one (if both work properly) would y'all get. same price when calculated for the exter gas to get the 214ws

...we are still searching for an operators manual on this unit...soooo, can anyone talk me down on how to set the timing (are there timing marks anywhere ?) -- particularly: what position should...

Here's my problem: Knotter is not making a full revolution when tripped. The trip dog roller makes contact with the trip arm (to reset the roller) too early it seems so the cam on the knotter...

I've got a 14T that I haven't used in a few years. Got it out of the weeds, cleaned up, greased, checked timing etc. When I ran a cycle by hand the knotter didn't complete a full revolution...

I am looking for a john deere 14t baler part (yoke rear) Parts number BP14507E email me at : dairythings@gmail.com our baler snapped this part and we cant seem tofind one that will fit the u...

I am new to the whole haying process and I am going to look at two differnet balers both suppost to be in good "field ready" condition, one is a Ford 530 baler and one is a JD14T baler. WHich is a...

The pitman is "busted half in two", bent beyond measuring. I'm in search of a measurement of the pitman from the center of the wrist pin on the plungerhead end (there's a grease fitting at this...

First off, I'm glad I found this site!! Secondly, go easy on me, I'm a gal!!! Anyway, the problem is, our baler will not tie one side..it ties the oneside every single time, but the other side...

i have this on my parts baler. is it worth transferring over? does anyone have a operators guide? .

Hi all, First off, just like to say that I'm glad i found this site, tons of usefull info! :) Anyways, I seem to have gotten myself into a much bigger project than I anticipated... When we moved...

What type of twine are you running. How short have you ever made the bales. i have been trying to make them small for the wife to move but the bales does not seem to like it. They come out...

For the last few years i have been buying hay for the horses. Well, as most of you probably know, Hay is starting to get expensive and I have about 30 acres of Timothy hay just waiting to be...

Found a 14T baler at local JD dealer, said it needs a shaft that operates the Knotters, anyone had any experience with this and how big of a job is it to replace it? Wants $500 as is, 265 for the...

I've been bringing a 14T back to life that hasn't been used in years. When I started it was shearig bolts all the time, so I retimed it. Looked like it was going to work great and then a chain...

I just wanted to put a message up here and let you folks know that my father-in-law's TC30 worked real nicely this weekend running a JD side delivery rake and square baler. We didn't do very many...

I am replacing the chains on my newly aquired John Deere 14T baler... The one at the front near the slip clutch went on fine. The one that drives the feeder arms though was much tougher...The...