I was wondering if anyone had a drawing/detail for how the governor assembly gets installed on the crank. Ours was destroyed when we pulled it apart. The 3T72 crank was split in two. We know...

We are rebuilding an engine out of a Y1610D. It is a 3T75U engine with a 3T72 crank. We are looking for a detail/drawing of how the governor is properly assembled on the crank as it was broken...

Yanmar 1610D manual

looking for starter part # for 3T75U engine on YM1610D tractor

Hello all, I am seeking a new (second hand) complete front axle for my Yanmar 1610D. I am based in Hampshire, UK. Does anyone know of anywhere that may stock one or has anyone on here got one...

Hello...I just purchased a 1610D with FEL (Stock I believe). The bucket hydraulic ram seals need to be replaced as the bucket begins to lower when static instead of maintaining its position. The...

Started my yanmar 1610d today and it wants to run wide open. It has set idle for a couple months, ran perfect when last used. The throttle is not stuck, linkage of both hand and foot control...

Hello, I have made a tooth bar using steel. I had it laser cut for ease and then welded it up on the bucket to ensure it fitted. Nothing difficult and it is rough and ready but it will do the...

Hello, My tractor has developed 2 leaks at the same time, seems a bit unlucky. One is on the front right wheel and I have attached an image. The other is underneath roughly in the middle of the...

Hi everyone, I'm in the UK so don't have the ability to buy the turf kit from Hoye. I am trying to get a UK company to manufacture some wheels but I can't find the inter axle ratio number...

I have a YM1610D. The left pinion shaft thru the brake drum has sheared some splines. I am looking for a replacement. Hoyt Tractor does not have a new or used part. Anyone out there have this...

I recently acquired a Yanmar 1610D. I have torn the engine all the way down to the bottom end and have pulled the motor from the frame. I am looking for someone that is knowledgable about these...

Simple question... how many quarts of oil in yanmar 1610D engine? Gonna use Delo 400 15-40 unless told not to. Time to do some maintance! Thanks in advance, Papa

I have Yanmar 1610D that I am restoring. This guy runs like new but cosmetically needs a little help. I ave purchased most of the minor sheet metal that needs replacing but I can't fenders...

Does anyone know of a place in virginia that sells refurbished Yanmar tractors for sale?

Hello, I am buying a yanmar 1610d tractor from a private party. What things should I look for and should know about? I am actually going to represent my uncle who will not be there, and I have...

I have Yanmar 1610d tractor which I have a problem with. I tryed starting it yesterday but when it started it race the motor so I hade to kill it. But now it wont start. it just turn over and seem...

Figured I'd knock out the first post with an introduction. My father and I share tractors between our two properties (he has 2 acres and I have 12.5 acres). We've had a Yanmar 1610D for 5+...

Hello all, i have a simple but not an easy question: is there somewhere out someone who compared the John Deere 750/850 with the Yanmars the same size? I ask, because I want to register my Yanmar...

I need to replace the two front knuckle seals on my 1610D. I am trying to decide whether to do it myself or have an experienced mechanic do it. My mechanical skill level would be classified as a...

what are the goods and bads with this machine? Never owned a tractor but am a mechanical guy.Machines don't scare me.what I'm trying to say is I don't want to know what the inside of a 1610D...

Something new happened yesterday, the tractor had been setting for a couple months so I went out to start it and and use it a little. Well, it started just fine but after it warmed up I put it in...

Does anyone know if it is possible OR a good idea to turn the front wheeels inside out to make the stance wider an this tractor? I alredy have the rear wheels reversed.... :confused:

I have a 1610d and the front diff housing directly under the engine is broken. My question is can the axle tubes be removed from the housing without dis assembling the outer gears (at the wheels)...

Which of these tractors has a better longevity and fewer problems? I'm interested in buying one or the other. In all tractor manufacturing, there is one tractor that outlasts and out performs...

Does anyone no the correct oil and air filter no. for this model tractor. Also, What type of gear oil does the RS 1300 model tiller use. Is there a service manual available for the model tiller.