Tractor shows all fuses good, fuel shutoff solenoid getting 12.2 v, new fuel filter, air filter, will idle and drive about 100 ft then die, I am wondering if fuel pump or injectors are bad?

I was wondering if there is a cluster meter board that doesn’t cost over $500 dollars to buy, a universal one? I believe the board on mine is digital. Thanks You, any advice is welcome. Sally

I have the above model and I am dropping hydraulic fluid by the PTO output shaft but it appears to be coming fron around the site glass that is right next to it. Has anyone had this problem and...

I will take delivery of a 2910 on Thursday and need some info if any of you can help. What is the recommended oil viscosity and capacity? Oil filter number? Is the hydraulic and transmission...

Just bought a 2910 and will be needing some info until I can round up manuals. It will need an oil and hydraulic change. If anyone could give me the book specs on the fluids and capacities I would...

I sheared the PTO shaft on my Branson 2910i tractor, I have part and book, but I need to know do i need to remove top plate on transmission case to complete repair, book doesn't say. I can't get...

I have owned a 2006 Branson 2910i for about 4 years now. Tractor is great until you need to find parts and info! I have a dealer about 50 miles away that we have gotten parts from but I need a...

Branson 2910i PTO blows fuses...anyone else had this problem? Have friend that is more mechanically inclined helping to troubleshoot problem, but we are stumped as to what to check next. Have...

Good Morning, I was using rototiller heard a huge cracking sound,shut down operation,their was pto shaft to tiller thrown to fence and pto shaft inside tractor was shredded off inside tractor. I...

Hi my name is Craig and I'm new to this so bear with me. I have a Branson 2910i tractor with a BL10A Loader. I was cutting down some tree's and was using my add on forks on the bucket and damaged...

I have a 2910i and I have issue with brown paper looking residue constantly. I have took both tanks off and cleaned them bleach and hot water. Dried them out with air and then set in sun. (Late...

My cousin is looking at a used Branson 2910i in Ohio. He's asked my advice. I don't know Branson tractors though I see one now and then. Given this model's terrible reputation for hard winter...

Does anyone have an idea of how much a Branson 2910i four wheel drive with bucket and roto tiller is worth. I has only 127 hours and is a 2006 model. Thanks Dave

Been a member for just a couple years, but never had a tractor so I just kinda lurked in the shadows learning from all of you. Well, I just picked up a Branson 2910i with low hours (74) from the...

Does anyone know the battery replacement for the 2910. I can't find a number in the Operator's manual. I bought one for a 30hp Kioti (25-s) but it is too small. You'd think they would be the same...

I've assembled a Liberty 8" Chipper and will soon hook it on the 3pt and take it to the lot. The chipper has a belt drive from the PTO input shaft to the flywheel shaft but there is no clutch of...

Here we go... I bought my Branson about a year ago and it seemed everything was working well. I had only been using the front end loader to clean up around the place and i decided to go ahead and...

Anyone here own a 2910i or 3110? I have a couple questions, small problems you might have encountered.

Hello, does anyone know where I can get a user's manual or a 'quick start guide' covering basic operation for the Branson 2910i? Thanks - Dan

How easily does your Branson start? I have a new Branson 2910i, it had spent a year on the dealer's lot. With a block temperature of 35 F and glow plugs on for 12 seconds (turn the key on three...

Just got a new 2910 like the tractor so far here are some pics Mike48

Been a LONG time since I posted. I formerly owned a Kubota L3830 with FEL and 6' BH. At the time, I was maintaining 15 acres of pasture. I have sold some land and the big Kubota, and am looking...