Hi,
I need to change my Ford 4600 fan belt, but there is a linkage between the motor fly wheel and the hydraulic pump in front of the tractor. I do see the bolts heads for that shaft on the fly...
My Ford 4600 power steering suddenly stopped. If I push down with the bucket and lift the front end, it steers fine. I mistakenly put some waste oil in it, (dumb but it really wasn't very much...
Hi,
I have somekind of electrical problem with my Ford 4600, everything is dead when I turn the switch, but there is definitly voltage on the battery. Therofore I want to open the hood to see the...
Hello All,
Thank you for allowing me to post. I am a newbe to the forum. I need to remove a leaking fuel tank.
Does anyone know if it comes out by the steering column into the cab, or can it come...
Hello. At the beginning I want to apologize for the spelling, but translators are translate google translate because I'm from another country.
I have bought a FORD 4600 tractor for a long time...
I need to replace my front tires on my Ford 4600. They tires on there now are Goodyear 6 ply 4 rib tires. I have no idea how old they are, and they are hard as a rock. They have no tread left, and...
Hello
Im new to the forum, so this is my first post apart from the introductions post.
I've been looking at a 4600 (1981-82 model) with Q cab.
It has a 3pt linkage and a front end loader fitted...
Hello
Im new to the forum, so this is my first post apart from the introductions post.
I've been looking at a 4600 (1981-82 model) with Q cab.
It has a 3pt linkage and a front end loader fitted...
Checked oil level in tractor and everything looked fine, started tractor and had some slobber coming from exhaust pipe, drove it down the road, had not been on it for around 10 minutes when the...
I bought a FORD 4600 with Bush Hog brand loader on it a while back for what seemed to be a fair price. Seems to be a really good solid tractor with only 735 something hours on it. I am the third...
I bought a FORD 4600 with Bush Hog brand loader on it a while back for what seemed to be a fair price. Seems to be a really good solid tractor with only 735 something hours on it. I am the third...
Ok, so I decided to change the oil in my rear axle/hydraulic system in my Ford 4600. I had not done this before, as I haven't had the tractor very long. My manual says to use 33.9 quarts of oil...
Hi all,
I have a ford 4600 diesel and am having a problem with the PTO not engaging. I was wondering if anyone else has run across this before and where to start checking for problems at?
Thanks...
Hi all,
I need to clean up several acres (20+) of 3 year old cutover. Regrowth is minimal and most stumps are showing some rot. I am considering getting a W.R. Long adaptor plate to convert my...
Hello I'm a new member would like to help me in a provlima I shows the rev counter .No outside the origi foot firmly enough amounts can stabilize tin needle in tamplo.ford 4600:)
I have a ford 4600 SU gas burner and am needing to know what kind of engine oil to use in it. I do not have a manual to reference and cannot find any information online that answers this question...
I have a ford 4600 SU gas burner and am needing to know what kind of engine oil to use in it. I do not have a manual to reference and cannot find any information online that answers this question...
I need a cable to go from the temp probe in the front of the block to the temp guage. Anybody know the part number or any info on this? Can't find it anywhere.
Thanks
RSKY
tractor belonged to my late father inlaw. brought it home this weekend to use around the house. cut off a few times due to clogged screen in fuel tank. got that fixed. went to start it and it wont...
Hi,
I need to replace my oil pan on a 4600 Ford Diesel due to some unfortunate encounters with some large brush when brushhogging, causing a leak. I ordered an aftermarket pan, and the thing is...
Hello, I have a ford 4600 tractor. Would like to purchace a grapple to help clear land and move bales. Do i need to purchace the whole loader or just a grapple bucket. The loader on it now is...
Ok I think I have a issue. Let's start from the top. I bought this tractor and seems to run and crank very well. But I first did a coolant flush and got rust colored coolant out. Filled with...
So my 4600 runs smooth except from 1600-1800 rpms. Anything above 1800 is fine also. Any idea what could cause a vibration in this 200 rpm range? Do these engines normally run this way. I know...
Hi,
Maybe there's an old thread with the same problem - We are fairly new to crofting and now I have a ford 4600 with a tipper trailer. The trailer is fine. The tractor has hydraulic input...
I need help hooking the wires back up to the solenoid switch.....can't seem to find a good diagram. An explanation of what each of the four posts is for would be very helpful.
Thanks!
I have a infrared thermometer and want to check my Ford 4600 engine temp. What area or areas do I check to get the best reading. Right now the manifold and just above the manifold on the engines...
Sorry second thread but screwed up title in first one. I have a diesel 4600. It idles at 850 -900 rpm's but should be at 600-700. How do I correct this?
Guys I'm considering buying a "supposedly" low hour Ford 4600. Apparently, it was used in a very small field to mow a couple times a year over the past 25 plus years. For the past 3 years it has...
What has happened to my tractor? The left front wheel is slanted at almost a 45 degree angle to the ground. The two front wheels used to look the same. :confused:
Has anyone ever seen gas get into the air filter housing? The only reason I noticed it was that I have been bush hogging some steep slopes and when I would go at about a 20 25 degree angle to the...
my father inlaw owned a ford 4600 tractor and has passed away a few years ago. i have been using it a few times a year bush hogging and scraping their road. i have noticed in high gear it doesnt...
I am looking to change the transmission fluid in my Ford 4600. From what I understand, the transmission fluid is separate from the hydraulic fluid on this tractor. I have seen plenty of...
The plastic retainers on my tractor shift levers are worn out, leaking water into the tranny and jamming my shifter. There is a snap ring holding a spring which holds a plastic retainer that...
My family has a Ford 4600 with a Kelley front end loader and a rear three point hydraulic mounting system. My grandfather passed away in 2001, and the tractor hasn't moved an inch until yesterday...
I have a Ford 4600 made in England that works very well and I am thinking of selling it. The hour meter does not work so I do not know the hours, does anyone have an idea of a value? Thanks.
My ford 4600 lift arms wont stay where you want them they drop or rise on there own you think they have but reving up can make them rise again or drop whan revs are dropped.The depth control seems...
Here is what is on my 4600. It only has a single remote.
Looking at it from the back
So here's my question...I just bought a ford series 204 disc harrow with flexo hitch with travel wheels...
Hi,
I recently moved to live on a mountain and am new to mowing on anything but flat ground. I have a Ford 4600 tractor with wheel weights and 3 front weights and no loader. I just installed a...
ok... my BIL has a Ford 4600 with the diesel engine.... he is telling me that its got a major coolant leak at a freeze plug at the rear of the cylinder block. He took it to a local guy that told...
Hi folks,
need some help with my Ford 4600 4WD, I have rebuilt the engine and repaired the cab. Trouble is that she was waiting for me for about 4 years in a field, while there the sheep...
Hi folks, engine now rebuilt, bodywork in progress. Must admit the Qcab is seriously poor, so many nooks and crannies for the water to sit and start the rust, all around the windows no longer...
Thinking about buying this tractor and would like to know if anybody could help me with the manufacture date of this tractor.
The serial number is 6K07cG0K22. I have been told that the HP is 52HP...
Comment: I own a Ford 4600 tractor and am having problems with the hydrualics. With out the slasher on the 3 pl it will go up and down,when I put the slasher on ,it only takes the weight and...