Today i am changing the gear oil in my IH 254. Following the directions, I removed the (3)drain plugs (diff and (1)ea side), (2)oil level plugs (1 ea side) and (2)fill plugs (top of axle) and...

IH254 with 1160 hours. I am looking to change the front axle oil. Manual calls for 85W-140, but doesn't say how much. Does anyone know how much is needed to fill? My best guess is maybe 1.5...

Looking for a radiator cap for an IH 254 (mid 80's). I see them priced online at $100 + . Is there something special about these caps that make them so pricey? Does anyone know of an aftermarket...

Newbie here. I am looking for a rear replacement rim for my IH 254. All the rims I see online have 4 "loops" to attach. The rusted rim that I am replacing has 4 "z" clips to attach. Is there a way...

Hello, I've newly acquired a 1984 IH 254 gear drive. I noticed that some fluid was leaking out of a hole in the transmission just under where the PTO engagement lever is. Was wondering if anyone...

Hi folks, I'm new to all of this. I have a small ranch and the IH 254 with FEL.

I have a IH 254 compact. I am replacing glow plugs. I have replaced glow plug indicator/resistor before and has gone out again. Due to cost, is this really necessary? If so, does anyone know the...

Hello. I am a new member and this is my first post. I recently purchased an International 254. The seller listed it on craigslist as a 1985 Case IH 254 diesel with 4WD. Its data plate...

Need an external (electronic) regulator for my IH 254. Alternator is Mitsu AH2035H. Tried a VR166 with no luck. Alternative would be a replacement alternator with internal regulator.

Hi, I'm new to the forum and need help. :Last year the 1984 IH 254 I have blew the Hyd pump line that is soldered to the pump. I had that repaired but the shop didn't add any fluid. My helper...

I am wondering the same thing as jenkinsph as I am looking to move up to a little larger tractor with a loader etc. The tractor is in great shape mechanically and cosmetically. It has the 3 cyl...

I have a 1985 IH254 with 857 hours that runs great when snow plowing etc. until I mow. I am mowing with a 5' MF 2220 Estate Groomer. After about 20 minutes of mowing the overheat light comes on. I...

does anybody know if i can put dual wheels on a international 254? if so how thanks

Glow signal is not working. Used to glow on instrument panel . Tractor starts ,but it takes time. thanks sanz

Hello. I just picked up an IH 254 compact tractor. My question is on the PTO. According to TractorData.com, this model should have a live PTO. However, in practice, the PTO disengages when the...

turn start key engine will start, climbs to high rpm & dies. feeling the manifold only 1 of the 3 cylinders is warm. combustion problem? please help!!!!

The starter spins but doesn't engage the flywheel. I've never dealt with this problem before. What can I do to fix this? I have some mechanical skills but am no mechanic. Any suggestions...

I have an INternatinal 254 tractor, 3 point hitch that over heats, we flushed the rad, changed the thermostat, put in a new heat gauge and bypassed the bulp to make sure it was overheating, new...

My 254 has gotten to where it will not pull itself at times especially when it's under a load. Sometimes I can play with the lift and it will go. I was told there may be a hydraulic clutch assist...

This is the first time I am posting in the International forum. I have a question about the IH 254, I have done some research and found out that the Mitsubishi MTE 2000D is the same model. What...

I'm new to tractors. I've had this one several yrs but am not very familiar with working on it. The 3ph hydraulics on my compact 254 suddenly stopped working. The 3ph is the only hydraulics on...

I need to find a source for hood decals or a full kit for an International Harvester 254 compact diesel. (NOT the Case -IH decals,but the true IH style) These have the red stripe at the top much...

When my tractor sits up a few months the lever for lifting and dropping the PTO sticks. almost to the point of not being able to move it at all. anyone have any ideas on how to loosen the thing...

23 HP 3 cyl diesel Hard working little tractor