axle

Hello all, I have been looking at smaller 25 hp tractors to go with my big tractor for close to the house. A lot of them have aluminum housing in the rear. Besides the lighter weight, has anyone actually broke the aluminum housing or had any issues at all with it? Is it something that should...

I blew a bearing on 155 K-Series flail mower. It looks the bearing collar (is that what it is called?) for the drive side bearing is stuck on the shaft but I don't know what I am looking at. The bearing was fragmented and I have got the replacement bearing. I have measured the bearing and...

Just got my 4047 back after losing it in a divorce. I had a thread going on the trailers and transportation section. Upon getting it home I wanted to give it a good grease and inspection. When I got to the right front I found this😱, three out of the five bolts holding the front drive to the...

Getting ready to do my 400 hour service and one of the tasks is to change the front axle oil. The manual tells me to use, "SAE 90 gear oil or better, or same as transmission oil. Now I'm no chemist but these two items are just a tad different . . . Any idea if they can be swapped in the front...

I must apologize for my ignorance. I’m not exactly sure what the parts are called, but where the axle and the wheel hub meet. It’s like on the back of the wheel has a knuckle that sets down on the axle. There are seals (there) and both of mine are leaking. Can anyone give any insight on...

My front axle locked up. It ended up being the pinion was ground up and catching on the ring gear. I got it apart and cleaned all the metal shaving out of the axle. I got a new ring/pinion and bearings. I got the new ring gear installed. I tried installing the new pinion but the front pinion...

Hey guys, Need some advice/opinions on a IH 254. I changed the front axle gear lubricant last summer. 85-140 per operators manual. I used tractor all summer, fall and winter. No issues. The other day I noticed some leakage coming from the top of the axle. Is this some kind of vent or something...

I was gifted a 4100H in need of front axle repair and the housing attached to the hub is trashed on both sides. according to the thread below, this was a part discontinued years ago. Does anyone have a lead on where I could source two of the Parts AM880071 from? link to the diagram: John Deere...

The passenger side rear axle seal is leaking. Does anyone know where I can get a replacement seal / part number? Possibly a bearing as well. I’m wondering if the bearing could be getting bad causing the seal to fail.

Reaching out to find anyone else that may have had front axle fail with the 6 bolts, flange/washer holding gear in place axle configuration in a IH Case tractor. I have the 105C model. I bought with low hrs. and at IH dealership with limited warranty. The first right side fail was done right...

Hi, I bought a Mahindra 1626 HST in May of 2024. I live In Central NY on the shore of Lake Ontario where we’ve been getting a lot of snow. Last week I was pushing snow around with the bucket, and the front Axle locked up on me. The tractor was in 4wD when this happened. When taking it out of...

Probably best to just replace both as long as I'm having to drain the whole thing to replace one side, TC6Y628012 194312-32660 which I'm finding at around $35 each on most sites, but the site I bought the transmission fan at wants $32 shipping for these 2 seals? The site gives no alternate...

Hello! Looking for some help sourcing a couple of rear axle shafts. I had no power to the back wheels so I am assuming the other axle looks the same as this one. 😬

Hi I got a Gravely commercial 432, and it leaks on the left, I'm having a hard time to find that seal. Anyone knows a site I can order from ?

I have been wanting one for a while. WIth the mill I want a way to pickup logs when they come available. Been keep my eye on Marketplace and found this guy. Picked it up for $850, which isn't bad for a stoutly built tandem axle. Needs new wood, some rust remediation and a new coat of paint...

Bought new, has 2700 hours. Started seeing drips inside right front tire, seems to seep about a 1/2 cup every week. Been going on about 6 months, only takes a a few squirts of 80/90w gear oil to refill when I check it before use. Just noticed a few drops on floor inside rear wheel, right...

My JD4600’s front axle is leaking through the seals on the point where the driveshaft comes in and also at the ends of hubs (wheels). My local tractor mechanic indicated that the seals need to be replaced (the tractor is 25 years old) and had been leaking a bit in the past from those areas...

I have a Troy-Bilt Pony riding mower that is only six months old and a squealing noise coming from around the area of the trans-axle is getting worse and worse, almost constant. I can't really tell exactly where it's coming from but I'm pretty sure it's not the kind of squeal a belt would make...

Crazy!!!! I broke some teeth on my front axle ring and pinion ring and sourced replacements from salvage yard in Canada years ago they sent one and the gear grooves swoop the wrong way I sent it back thinking they sent the wrong part. I revisited it again earlier this year and talked to a nice...

Hi guys and Happy Thanksgiving ! The front left axle seal has been leaking badly, I just pulled the casting apart, pulled the bearings and big bevel gear and see the front axle seal. It reads AE2074F. This is actually the axle seal, not the steering pivot seal I've read several threads about...

I have a Ford/New Holland 5610S, recently changed trans hydraulic fluid and filter. Filled the reservoir back up with 15 gallons as it calls for 16.3 gallons. However, the fluid is showing 3/4" over the full mark. I noticed a small arrow looking mark as seen in the attached photo about 1" above...

Hey there! I have a 1992 Ford 3230 tractor and I've noticed some fluid on the left wheel. I think it's a bearing/seal replacement but I'm not sure. I can do some work on tractors, but don't have a lot of time and heavy tools (like what may be required to remove the axle). I'm wondering what I'm...

Hey guys some what new to thread. I am needing help i am rebuilding my front axle I let bearings go dry seals went bad got water in axle destroyed the bearings. [ rookie move ] I am having a hard time trying to get the front pinion shaft out of the housing if someone has a manuel that shows the...

Have a NH boomer 37 (2016-ish) where the front axle seal started leaking. Opened it up and found the shim had disintegrated and screwed up the seal. Ordered replacement seal and shims, but they don't fit. OIL SEAL MT40188939 It was superseded by MT40334121, Ordered both, neither fit, the axle...

Just writing about a friends experience with his 2009ish L3540. 1900 hours. It has the LA724 FEL... He has had issues with front axle bearing disintergrating. He is way up on maintenance, he uses all Kubota fluids yet he has had 3 failures with front axle bearings falling apart. Twice, a little...

Ive got a new to me 2008 branson 2910i and am going to do a hyd fluid & filter change but not sure what to use in the front axle. Do it take the same fluid or do you use gear oil? Would like to find an owners manual but no luck so far.

Have had a problem with the front differential spewing oil out of the vent cap on the right side. The manual says to check the oil level so that it is between the min and max markings on the dipstick.. Well, sure- I might be ugly, but I'm not stupid.. But is that checked with the dipstick...

Hey everyone, I've got a leaking front axle at the pivot point of the final case. I've raved the case, bearings etc and can't see where to split final case a from b. I have the service manual but it's not terribly explicit.Appreciate any help you might offer.

Does anyone here have information on front axle load rating for M59 TLB? My local TN dealer just shrugs and says they don't know. Messicks is going to call Kubota technical rep for an answer but nothing so far. Ive looked over operator and Workshop manual and found no info on front axle rating...

I've seen some trailers come up for sale here that have mobile home axles. Not being a fan of these, someone told me there are hub/bearing kits for them so one can use normal wheels and tires on them. Some kit's even have brakes. Anyone here ever see or use these on trailer home axles?

I am looking for the front axle and bearing for a Yanmar 1510D. The 4 bolts came loose and the broke the axle and bearing. If anyone has a front end final drive both the right and left side are the same. In the attached picture the axle without the bearing is the broken one, right at the...

so ive been diligently going through this used tractor i bought with 600 hrs. ive replaced all fluids and filters, worn parts in shift linkage, suction screen, small repai to SSQA, battery replace, few cosmetic paint or broken plastic repairs ect. im down to the last few things on my list, AC...

mentioned in this thread. https://www.tractorbynet.com/forums/threads/massey-ferguson-gc-2300-bent-steering-box-brackets.440866/post-6057913 guess what I found missing this afternoon? anyways massey does not list any part specs nor any adjustment specs. its an M10x30-1.50 pitch. odds are its...

Thought it would be a good idea to change out the rear oils with 2700 hours on the clock. No sweat with the differential oil. It apparently had been changed before I bought it because it was regular smelly gear oil not UDT oil. Dug all the dirt out of the two drain plugs in the gear cases...

Today i am changing the gear oil in my IH 254. Following the directions, I removed the (3)drain plugs (diff and (1)ea side), (2)oil level plugs (1 ea side) and (2)fill plugs (top of axle) and drained all the oil. I reinstalled (3) drain plugs and was adding new oil thinking I would add oil until...

I blew a o ring in my front axle pivot when greasing it. It’s a ck3510, 2021 model. How much is involved in fixing this?

My John Deere Model A has a leaking left axle seal. Any idea the cost for repari? Any idea where I can get a replacement?

Hello, I have a 1987 Ford 1520 that's developed a leak at the right wheel on the inside. I have not pulled the wheel off to check on it I am hoping it could be a seal. Does anyone know if there is a wheel seal in there? I have a front-end loader that I installed and it has not been abused but...

IH254 with 1160 hours. I am looking to change the front axle oil. Manual calls for 85W-140, but doesn't say how much. Does anyone know how much is needed to fill? My best guess is maybe 1.5 gallons. Just a visual guess...... I just want to make one trip to parts store. Thanks.

I have a Kubota 2380 leaking all the hydraulic oil from a spot near the front axle, circled in red on my picture. I'm trying to find what this part is called and how I can repair it. I'm looking in the manual and on forums/youtube and cant find anything yet.

Looking for axle front hub for a 5000 series, 6000 series or 7284 should all be able to make work. anyone with a junk tractor with the parts E-mail me and we can work something out. my tactor is 6284D cub cadet

Hey people I have a 18 year old Chinese tractor Dong Feng DF354 that needs the axle seals replacing. The trumpet housing will not pop out so now trying to remove the PTO, which also WILL NOT COME OUT... Tips or advice please.

Hi All, I need to replace both sides of front axle oil seals (between gear case and final case - leaks) but I am not sure if I have to take off the whole gear case (as described in manual) to do it. I would rather not have to do that in case I mess something up. I've attached photos of manual...

Does anyone know anything about these trailers? Any idea of a manufacturer so I can get specs? Does it have electric brakes? Looks like something you'd load a D3 on haul behind a dump truck. It is a tilt trailer too. I've been on the hunt lately for a 12-14 foot tandem axle equipment...

There is one for sale locally, but I would prefer to have Tractor with CI Rear.

Have a BX25 with 500 hrs. I get a clunking sound from the front axle. Hard to say if it's from from changing directions or turning or a combo of the two. Fluid seems to be full in the axle. Or could it have to do with the 4WD? Just thought of that and not sure I've taken it out of 4WD to see if...

Has anyone performed work on their front axle / 4x4 system on a Massey 1652 or similar? (Should be same as 1547, 1648, 1652, 1749, etc...). I've got about 1500 hrs on my 1652. Great machine, no previous issues. During some heavy loader work recently, I've developed an issue with my 4x4. I...

doing my pre-season service notice I am missing one 4260289M1 (agco part number) clip. look like this been unable to find xover number to other brands.

Trying to locate a good front axle for a yanmar ym240

Anybody know where I can purchase the large U Bolt on the Farmall Super A front axle? Thanks

Hi Guys, I'm in Canada, and looking for a 12mm pipe plug/drain plug socket for the 4 drain plugs on the T25 front axle. Im not a fan of using open ended crescent wrenches on hard to remove plugs, inevitably they get gauled up Looking everywhere I cant find a 12mm. I find 10mm and lots of...

Well, it happened. Leaking axle seal. I haven't done one of these jobs before. I can't find a LS or New Holland dealer near by, and I just don't want to drive an hour each way for a $17 part. Looks like Messick's has it in stock. So, while I'm elbow deep in the hub is there anything else I...

I have a B7800 that has been leaking hydraulic fluid from the front axle. I had it in to the dealer a few times, and it is still leaking. The first visit was a seal replacement, and it leaked within a day or two or getting it home. They took it back and put a 'speedy sleeve's in, and it...

Tractor 2016 XG3025 362 trouble free hours . I saw a little axle oil on the inside of my left front rim , for most of the winter it's been setting . i looked under the front end for a vent tube didn't see none , went and check manual there's none only vent the axle has is the blue threaded cap...

We have enjoyed our 2002 TC35D hydrostatic front wheel drive tractor and “built” our 20 acres with it. My husband uses the front end loader nonstop, pushes pulls and hauls. We have had the front axle worked on before. The very gifted Mechanic Has been able to actually weld in order to re-create...

I was greasing my tractor today and noticed what looks like part of the axle seal laying on the axle. I dont really see what else it could be, I guess I must have pushed the seal out last time I greased it. Have any of you ever replaced that seal? Is it a big job to do? Do you guys think I can...

HI, I need to replace the axle seals on a Iseki TXG23. In the manual it looks like an outer and inner 'snap-clips' are used to hold the axle in. Does anyone know if this is correct or are there another fixing inside the gear/differential lock assembly that are holds the axles in. I have tried...

Hello tractorbynet, I have the front axle hub apart on my L3130 (4x4). I want to replace the seal that goes between the hub (part with lug nuts) and gear/knuckle housing. The part # is 34070-13370...I attached a diagram, it is 060 or 180 on it. It is basically two parts...an outer rubber seal...